background image

06/2006

13

www.U-LineService.com

CO2175DWR — Ice Maker/Refrigerator

Electrical Specifications

CAUTION

Electrical installation must observe all state and local 
codes. This unit requires connection to a grounded (three-
prong), polarized receptacle that has been placed by a 
qualified electrician.

The unit requires a grounded and polarized 115 VAC, 
60 Hz, 15A power supply (normal household current). 
An individual, properly grounded branch circuit or circuit 
breaker is recommended. GFCI (ground fault circuit 
interrupter) is usually not required for fixed location 
appliances and is not recommended for your unit because 
a GFCI could be prone to nuisance tripping. However, be 
sure to consult your local codes.

See 

Figure 26

 for recommended receptacle location. 

WARNING

SHOCK HAZARD — Electrical Grounding Required. 

• Never remove the round grounding prong from 

the plug and never use a two-prong grounding 
adapter.

• Never use an extension cord to connect power to 

the unit.

Go on to 

8 Level the Unit

.

Leveling Information

IMPORTANT

It is extremely important that the unit is level. If it is not 
level, the ice mold will not fill evenly. 

1. Use a level to 

check the 
levelness of the 
unit from front to 
back and from 
side to side. Level 
should be placed 
along top edge 
and side edge as 
shown (see 

Figure 27

).

2. If the unit is not level, adjust the feet on the corners of 

the unit as necessary (see 

Figure 28

).

3. Check the levelness after each adjustment and repeat 

the previous steps until the unit is level. Go on to 

9 Install the Unit

.

Installation Tip

If the room floor is higher than the floor in the cut-out 
opening, adjust the rear feet to achieve a total unit rear 
height of 1/8" less than the opening’s rear height. Shorten 
the unit height in the front by adjusting the front feet. 
This allows the unit to be gently tipped into the opening. 
Readjust the front feet to level the unit after it is correctly 
positioned in the opening.

7 Prepare Power Supply

1-1/2"

7"

24"

Figure 26

8 Level the Unit

ULIN_0045_A

Figure 27

ULIN_0046_A

Figure 28

Summary of Contents for Combo CO2175DWR


















Reviews: