background image

06/2006

15

www.U-LineService.com

CO2175DWR — Ice Maker/Refrigerator

4. Using two of the screws (C) supplied, fasten the screws 

through the bracket and into the counter, cabinet or wall.

IMPORTANT

Certain cabinets or countertops may require special 
fasteners or additional wood blocking to anchor properly.

CAUTION

Make sure the screws are back far enough so they do not 
damage any exposed front surface of the cabinet.

Installation Troubleshooting

Problem

Q:

Water is leaking under the unit.

Solution

A:

A water leak under the unit is most likely caused by a bad 
connection in the water supply line. Make sure the water 
line’s brass fitting is screwed tight to its valve and 
threaded correctly. 

Problem

Q:

The drawer remains open unless it is pushed closed.

Solution

A:

The drawer should be self-closing when it is open 
approximately 8". If it is not, re-check leveling from front 
to back of the unit and readjust if necessary. 

Initial Start-Up

All U-Line units are shipped from the factory with the 
controls that are preset. No initial adjustments are 
required.

Once installation and leveling is complete, the unit is 
ready for initial start-up and operation. Open the top 
drawer, press and hold the 

POWER

 icon (see 

Figure 31

,1) 

on the display panel for aproximately ten seconds until 
the °F symbol flashes and release.

IMPORTANT

U-Line recommends that the unit be allowed to run 
overnight and make ice prior to loading the 
refrigerator and/or freezer with product.

1. As soon as the icemaker 

mold reaches the proper 
temperature, the ice 
maker mechanism will fill 
the mold with water.

Note: 

There is an interior 

light in each drawer which 
illuminates when the drawer 
is opened.

Note: 

The first cubes may be 

small because of air in the 
water line. After two hours, cubes will be standard size.

2. The ice maker will continue to produce until the bin is 

full. You may interrupt production by raising the bin arm 
into an upright and locked position (see 

Figure 30

). 

While the bin arm is locked, the unit will maintain 
temperature for ice storage.

IMPORTANT

It is possible that dirt or scale will dislodge in the water 
line. Always throw away all ice cubes made during the 
first twenty-four (24) hours of operation.

10 Start-Up for the First Time

Figure 30

Summary of Contents for Combo CO2175DWR


















Reviews: