background image

U-LINE CORPORATION LIMITED WARRANTY

U-Line Corporation warrants each U-Line product to be free from defects in materials and
workmanship for a period of one year from the date of purchase; and warrants the sealed
system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass
valve, the dryer and the connecting tubing) in each U-Line product to be free from defects
in materials and workmanship for a period of five years from the date of purchase.  During
the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Line’s
option, repair any product or replace any part of a product that breaches this warranty; and
(2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States
(including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in
connection with the replacement of any defective part.  During years two through five of the
warranty period for the sealed system, U-Line shall:.  (1)  repair or replace any part of the
sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line
products sold and serviced in the United States (including Alaska and Hawaii)and Canada,
U-Line shall cover the labor costs incurred in connection with the replacement of any
defective part of the sealed system. All other charges, including transportation charges for
replacements under this warranty and labor costs not specifically covered by this warran-
ty, shall be borne by you.  This warranty is extended only to the original purchaser of the
U-Line product.  The Registration Card included with the product should be promptly com-
pleted by you and mailed back to U-Line.

The following are excluded from this limited warranty: installation charges; damages
caused by disasters or acts of God, such as fire, floods, wind and lightening; damages
incurred or resulting from shipping, improper installation, unauthorized modification, or mis-
use/abuse of the product; customer education calls; food loss/spoilage; door and water
level adjustments (except during the first 90 days from the date of purchase); defrosting
the product; adjusting the controls; door reversal; or cleaning the condenser.

If a product defect is discovered during the applicable warranty period, you must promptly
notify either the dealer from whom you purchased the product or U-Line at P.O. Box 23220,
Milwaukee, Wisconsin 53223 or at 414-354-0300.  In no event shall such notification be
received later than 30 days after the expiration of the applicable warranty period.  U-Line
may require that defective parts be returned, at your expense, to U-Line’s factory in
Milwaukee, Wisconsin, for inspection.  Any action by you for breach of warranty must be
commenced within one year after the expiration of the applicable warranty period.

This limited warranty is in lieu of any other warranty, express or implied, including,
but not limited to any implied warranty of merchantability or fitness for a particular
purpose; provided however, that to the extent required by law, implied warranties
are included but do not extend beyond the duration of the express warranty first set
forth above.  U-Line’s sole liability and your exclusive remedy under this warranty is
set forth in the initial paragraph above.  U-Line shall have no liability whatsoever for
any incidental, consequential or special damages arising from the sale, use or
installation of the product or from any other cause whatsoever, whether based on
warranty (express or implied) or otherwise based on contract, tort or any other the-
ory of liability.

Some states do not allow limitations on how long an implied warranty lasts or the exclu-
sion or limitation of incidental or consequential damages, so the above limitations may not
apply to you.  This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.

Summary of Contents for ECHELON CLR2060





































Reviews: