background image

PAGE 1 OF 19 

1015 IH-2812

π

  H-2812

DIGITAL  

TIME CLOCK

1-800-295-5510

uline.com

SETUP

WARNING! This equipment has been tested 
and found to comply with the limits for a 

Class A digital device, pursuant to Part 15 
of FCC Rules. These limits are designed 

to provide reasonable protection against 
harmful interference when the equipment is 
operated in a commercial environment. This 
equipment generates, uses and can radiate 
radio frequency energy and, if not installed 
and used in accordance with the instruction 
manual, may cause harmful interference 
to radio communications. Operation of this 
equipment in a residential area is likely to 
cause harmful interference in which case the 
user will be required to correct the interference 
at his or her own expense.

CAUTION! Changes or modifications not 
expressly approved by the party responsible for 
compliance could void the user’s authority to 
operate the equipment.

NOTE: This digital apparatus does not exceed 
the Class A limits for radio noise emissions 
from digital apparatus as set out in the radio 
interference regulations of the Canadian 
Department of Communications. 

TABLE OF CONTENTS

Alert Definitions .....................................................................2 

Precautions ...........................................................................3 
Introduction ..........................................................................4 
Features ................................................................................4 
Equipment ......................................................................... 4-5 

 

ES700 .................................................................................. 4 

  Open and Close Unit .......................................................... 5 
  Power the Unit/Print Positioning ........................................... 5 

Important Things to Remember When Using The ES700 .......6

 

Quick Start .............................................................................6 

 

Atomic Synchronization ...................................................... 6 

  Set Time Zone (-5 EST, -6 CST, -7 MST, -8 PST) ....................... 6 
  Automatically Receive Atomic Signal ................................ 6 
  Turn DST OFF ........................................................................ 6 

Program the Time Recorder ..................................................7 
Settings ............................................................................. 7-15 

 

Time .....................................................................................7 

 Date .................................................................................... 8 
  12/24 Hour Format .............................................................. 8 
  Print Order ........................................................................... 9 
  Year Digit ............................................................................ 9 
 Hour/Minute ................................................................... 9-10 
  Leading Zero .................................................................... 10 
  Preset Comments .............................................................. 10 
 Language .......................................................................... 11 
  Print Length ........................................................................ 11 
  Print Method ................................................................. 11-12 
  Daylight Saving Time (DST) ............................................12-14 
  Set Password .................................................................14-15 
  Enter Password ...................................................................15 
  Cancel the Password .........................................................15 

Reset Factory Default Settings ....................................... 15-16 
Wall Mounting .....................................................................16 
Replacing the Ribbon Cassette .......................................... 17 

Troubleshooting ...................................................................18 

Specifications .....................................................................19

ES700

8 16

15

AM

SU  MO  TU  WE  TH  FR  SA

R

Serial number label for bottom of clock. 

Information contained in this manual is company private to Acroprint Time Recorder Co., and shall not be modified, used, copied, reproduced or disclosed in whole or in part 

without the written consent of Acroprint. Contents herein are current as of the date of publication. Acroprint reserves the right to change the contents without prior notice. This 

manual has been carefully prepared to cover all aspects of this unit. However, if any explanations are inadequate, unclear, or difficult to understand, please contact Acroprint. 

We recommend that you carefully read this manual to maximize the use of this unit. © 2008 Acroprint Time Recorder Co. All Rights Reserved.

Summary of Contents for H-2812




















Reviews: