background image

PAGE 7 OF 7 

0219 IH-7862

TROUBLESHOOTING

SPECIFICATIONS CONTINUED

OPERATING ISSUE

RECOMMENDATIONS

Doesn't turn on.

Make sure wiring is properly connected to hand dryer.

If not properly connected, contact installer.

Turns on and off in error.

Check that nothing is obstructing the cavity.

Remove objects from cavity.

Continues to run after hands have been 

removed.

A two second delay after hands have been removed is normal.

Not drying hands properly.

Clear obstruction in inlet and monitor state of HEPA filter.

Follow maintenance recommendations.

Shuts off after a few seconds.

Check that nothing is obstructing the cavity.

Remove objects from cavity.

Water accumulates in the base of the dryer.

Make sure drain outlet is not blocked.

Clean and unblock drain outlet with provided wire brush.

Reflects a red light.

Water tank is full.

Empty water tank and replace. Once water tank is empty red 

light will turn off.

Flashes a red light in the upper part of the 

front panel, while all other lights are turned off.

Contact Uline Customer Service at 1-800-295-5510.

Turns off when in use and starts again.

Disconnect from power supply. Reconnect and wait six minutes 

before using.

π

  CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA

1-800-295-5510

uline.com

Regulations

This unit complies with the following directives/normatives: 1999/5/CE, 2004/108/CE, 2006/95/CE, 

2002/96/CE, 2011/65/CE.

Others

This unit has Bluetooth™ technology.

Standard 

Warranty

Five years for parts and one year for labor (see conditions).

Summary of Contents for H-7862








Reviews: