background image

USER GUIDE

 Troubleshooting 2

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • 

SERVICE

CHECKING PRODUCT TEMPERATURE

To check the actual product temperature in the 
unit:

1. Partially fill a plastic (nonbreakable) bottle with water. 

2. Insert an accurate thermometer. 

3. Tighten the bottle cap securely.

4. Place the bottle in the desired area for 24 hours. 

5. Avoid opening the unit during the testing period. 

6. After 24 hours, check the temperature of the water. If 

required, adjust the temperature control in a small 
increment (see CONTROL OPERATION). 

Causes which affect the internal temperatures of 
the cabinet include:

• Temperature setting.

• Ambient temperature where installed.

• Installation in direct sunlight or near a heat source.

• The number of door openings and the time the door is 

open.

• The time the internal light is illuminated. (This mainly 

affects product on the top rack or shelf.)

• Obstruction of front grille or condenser.

Product is Not 

Cold Enough.

Air temperature does not indicate product 

temperature. See CHECKING PRODUCT 

TEMPERATURE below.
Adjust the temperature to a cooler set point.
Ensure unit is not located in excessive 

ambient temperatures or in direct sunlight.
Ensure the door is closing and sealing 

properly.
Ensure the interior light has not remained on 

too long.
Ensure nothing is blocking the front grille, 

found at the bottom of the unit.
Ensure the condenser coil is clean and free of 

any dirt or lint build-up.

Problem

Possible Cause and Remedy

Summary of Contents for Origins SP18

































Reviews: