background image

U-Line Electrical / Plumbing Specfications

13

1. Plug in the power cord.

2. Open the top drawer and press the 

POWER

 icon to turn the 

unit 

OFF

.

3.

C2275DWR Only:

 

Open the water supply valve in the main 

water source.

4. Gently push the unit into position. Be careful not to entangle the 

electrical cord. 

5. Re-check the leveling, from front to back and side to side. Make 

any necessary adjustments. The unit’s top surface should be 
approximately 1/8" below the countertop.

Anti-Tip Kit Installation

WARNING

• The Anti-Tip Kit must be installed on this unit before 

it is used. 

• Additional blocking or special fasteners may be 

required for installation. Installer is responsible for 
secure attachment to prevent the unit from tipping.

• Make sure the mounting screws attaching the unit to 

the counter, cabinet or wall are deep enough into the 
mounting surface to support the weight of the 
drawers and the items that will be inside the drawers.

• Never use the drawers as steps or as a shelf to 

support more than the drawers’ content. Serious 
personal injury could occur.

After leveling, the unit must be secured to a counter, a cabinet or a 
wall to prevent tipping.

1. Open the upper drawer to expose the six screws (A) installed 

at the top two corners (three at each corner). Remove the 
appropriate screws for horizontal or vertical mounting Do not 
discard.

2. Insert the screws through the anti-tip bracket (B) and attach the 

bracket to the unit. Tighten screws securely.

3. Repeat for the other side.

Note: 

The bracket should be flush with the surface it is being 

attached to. If it is not, loosen the screws and slide the bracket 

against the mounting surface. Tighten screws securely.

4. Using two of the screws (C) supplied, fasten the screws through 

the bracket and into the counter, cabinet or wall.

IMPORTANT

IMPORTANT

Certain cabinets or countertops may require special 
fasteners or additional wood blocking to anchor properly.

CAUTION

Make sure the screws are back far enough so they do not 

damage any exposed front surface of the cabinet.

Installation Troubleshooting

Problem

Q:

The drawer remains open unless it is pushed closed.

Solution

A:

The drawer should be self-closing when it is open approximately 
8". If it is not, re-check leveling from front to back of the unit and 
readjust if necessary. 

Problem

Q:

Water is leaking under the unit (C2275DWR units)

Solution

A:

A water leak under the unit is most likely caused by a bad 
connection in the water supply line. Make sure the water line’s 
brass fitting is screwed tight to its valve and threaded correctly.

11 Install Unit

A

B

Countertop or Wall Header

C

Cabinet or Wall Stud

A

C

B

Horizontal Mounting 
(Left Side Shown)

Vertical Mounting 
(Left Side Shown)

Summary of Contents for WINE CAPTAIN 2275DWRCOL


















Reviews: