background image

2

The New York City Department of Buildings has approved the Independence® Series boiler:

Approval No. MEA 154-93-E Vol. III.
The City of New York requires a Licensed Master Plumber supervise the installation of this product.
The Massachusetts Board of Plumbers and Gas Fitters has approved the Independence® Series boiler.  See the Massachusetts 

Board of Plumbers and Gas Fitters website, 

http://license.reg.state.ma.us/pubLic/pl_products/pb_pre_form.asp

  for the latest 

Approval Code or ask your local Sales Representative.
The Commonwealth of Massachusetts requires this product to be installed by a Licensed Plumber or Gas Fitter.

The following terms are used throughout this manual to bring attention to the presence of hazards of various risk 

levels, or to important information concerning product life.

DANGER

Indicates an imminently hazardous situation 

which, if not avoided, will result in death, serious 

injury or substantial property damage.

CAUTION

Indicates a potentially hazardous situation 

which, if not avoided, may result in moderate or 

minor injury or property damage.

WARNING

Indicates a potentially hazardous situation 

which, if not avoided, could result in death, 

serious injury or substantial property damage.

NOTICE

Indicates special instructions on installation, 

operation, or maintenance which are important 

but not related to personal injury hazards.

CAUTION

If, during normal operation, it is necessary to add water to this boiler more frequently than once a month, 

consult a qualified service technician to check your system for leaks. A leaky system will increase the 

volume of make-up water supplied to the boiler which can significantly shorten the life of the boiler. 

Entrained in make-up water are dissolved minerals and oxygen. When the fresh, cool make-up water is 

heated in the boiler the minerals fall out as sediment and the oxygen escapes as a gas. Both can result 

in reduced boiler life. The accumulation of sediment can eventually isolate the water from contacting the 

cast iron. When this happens the cast iron in that area gets extremely hot and may eventually crack. The 

presence of free oxygen in the boiler creates a corrosive atmosphere which, if the concentration becomes 

high enough, can corrode the cast iron through from the inside. Since neither of these failure types are a 

result of a casting defect the warranty does not apply. Clearly, it is in everyone's best interest to prevent this 

type of failure. The maintenance of system integrity is the best method to achieve this.

NOTICE

This boiler has a limited warranty, a copy of which is included with this boiler.

It is the responsibility of the installing contractor to see that all controls are correctly installed and are 

operating properly when the installation is complete.
Surface rust on cast iron sections may be attributed to the manufacturing process as well as 

condensation during storage.  Surface rust is normal and does not affect the performance or longevity 

of a boiler.

Summary of Contents for INDEPENDENCE









































































Reviews: