background image

SKU 97706  

      For technical questions, please call 1-800-444-3353. 

PAGE 16

Ford Throttle Body Injection With Small Schrader Valve - FIGURE J:

gaUgE

(1)

PRESSURE TESTINg

aND

BLEED-OFF aSSY.

(25)

aDaPTER

(26)

FIgURE J

1. 

Turn off the ignition.

Relieve the fuel pressure.  Refer to the vehicle’s service manual for specific pres

-

2. 

sure relief procedures.
Remove the air cleaner assembly.  The test valve is located at the top of the 

3. 

throttle body unit.
Connect the Gauge (1) to the Pressure Testing and Bleed-off Assembly (25).

4. 

Attach the female end of the Ford Adapter (26) to the test valve.

5. 

Attach the female quick coupler on the Pressure Testing and Bleed-off Assembly 

6. 

(25) to the male quick coupler on the Adapter (26).
Start the engine and allow it to idle.  Check all connections for leaks.

7. 

Read the Gauge (1) and compare the result with the pressure values in the ser-

8. 

vice manual.
Stop the engine and turn the ignition OFF.

9. 

With free end of bleed-off hose in a suitable container, press button on side of 

10. 

bleed-off assembly slowly to de-pressurize the fuel system.
Refer to the 

11. 

General Safety Rules 

section before removing tester from vehicle.

Start the vehicle and check for leaks.

12. 

07f

Summary of Contents for 97706

























Reviews: