background image

23 - Express 12 gallon Multi surface cleaner - operator and parts Manual

MacHinE MaintEnancE 

To keep the Express in good working condition, simply follow the machine’s daily, weekly 

and monthly maintenance procedures. 

When servicing the machine, unplug the cord from the wall outlet. Failure to do 

so can result in injury or death caused by electrical shock.

daILy maIntEnanCE (EVEry 4 Hours of 
oPEratIon) 

Empty  and  rinse  out  the  recovery  tank 

1. 

thoroughly. 

Remove the float shut-off screen from the 

2. 

recovery tank and clean (see Figure 19). 
When the solution tank is empty, remove 

3. 

and clean the solution filter screen located 

at the end of the hose inside the solution 
tank. 

When replacing the 

solution filter screen

, be 

certain the filter screen lies in the recessed 

pocket at bottom of the tank. This will assure 

that all the solution is accessed from the tank 

the next time the machine is powered on. 

Wipe the power cord and check for damage; 

4. 

replace  if  necessary.  Coil  the  cord  neatly 
after use. 
Clean the exterior of the machine with an 

5. 

all-purpose cleaner and damp cloth. 
Remove  any  accumulated  debris  on  the 

6. 

gear box shaft and inside the threaded portion of the hub (see Figure 18). 

An  accumulation  of  debris  around  the  gear  box  shaft,  if  not  removed,  may 

damage the gear box oil seal resulting in loss of oil in the gear box. If the gear 

box is operated without oil, severe damage may occur. (Repairing the Express 

requires removing the cleaning head, described in the Repair Guide Section of 

this manual, starting on page 27.) 

remove debris on gear 

figure 18.  

Box shaft and Inside threaded 

Portion of Hub

remove screen  

figure 19.  

and Clean

Summary of Contents for 100-041-016



























































Reviews: