background image

reV: 17f

SMoGHoG

®

SHM Series Models 

1

1.  IMPORTANT NOTICE

this  manual  contains  important  safety  information  and 

precautionary measures. it is impossible to list all potential 

hazards associated with every collection system in each 

application.  Proper  use  of  the  equipment  should  be 

discussed with 

United Air Specialists, Inc. (UAS) or your 

local  UAS  representative

.  operating  personnel  should 

be  aware  of,  and  adhere  to,  the  most  stringent  safety 

procedures.

2.  INTRODUCTION

thank you for selecting uaS oil mist collection equipment 

to  assist  you  in  your  commitment  to  a  clean  and  safe 

environment.  We  trust  that  in  purchasing  our  product,  

you  have  recognized  our  commitment  to  offering  air 

cleaning  equipment  which  is  engineered  to  each  oil 

mist  collection  need  and  manufactured  to  the  highest 

standards. if at any time you have a question about oil mist 

collection,  please  do  not  hesitate  to  call  your  local  uaS 

representative. 
the  purpose  of  this  manual  is  to  provide  the  proper 

operating  and  maintenance  guidelines  for  the  SHM 

system  supplied  by  uaS.  as  you  review  this  manual,  

refer  to  figure  1  for  assistance  in  identifying  oil  mist 

collector parts.
the SHM oil mist collector has been designed to provide 

you  with  exceptional  oil  mist  collection  capabilities  and 

reliable,  long‐term  field  operation.  We  suggest  that  you 

thoroughly  review  this  manual  prior  to  installation  and 

startup of your system.
if  your  SHM  has  optional  equipment  included  as  part  of 

your order, specific operations and maintenance manuals 

for these accessory systems will be included. if applicable, 

site  specific  installation  and  other  drawings  will  also  be 

included.
if  you  require  assistance  in  the  installation,  startup, 

operation,  maintenance  or  troubleshooting  of  your 

air  cleaning  equipment,  contact  your  local  uaS  sales 

representative.

2.1 SMOGHOG NOMENCLATURE

SMoGHoG oil mist air cleaners are available in a variety 

of  configurations  and  sizes.  the  model  string  for  each 

given unit represents the base configuration. the model 

number completely identifies the design and can be found 

on the unit nameplate. SHM models are defined according 

to descriptions listed below (see bold):

 SHM-0XC-A

 

   

                 advanced unit

 

       cartridge Style filter

 

              nominal rated airflow

5

 - 500 cfM, 4 filter cartridges 

8

 - 800 cfM, 6 filter cartridges

Models  SHM-05C, SHM-08C, SHM-08C-A ADVANCED

the SMoGHoG is a machine mounted, self contained, oil 

mist filtering unit with left, right or rear inlet, combination 

sump and filter cabinet, primary filter, blower cabinet, and 

controls.  optional  after  filters  are  available  for  second 

stage filtration.

2.2 EQUIPMENT DESCRIPTION

this  section  will  briefly  describe  each  component  in  the 

SHM and its role in the system’s operation.

Filter Cabinet

each  unit  has  a  filter  access  door  that  provides  access 

to  the  primary  filters  for  service  and  replacement.  the 

PeacH  coalescing  filter  cartridges  are  slid  into  place 

between two tubesheets, concentric with the holes on both 

top and bottom.

Filter Elements

Primary coalescer cartridges featuring PeacH

®

 Saturated 

depth coalescing technology

Sump

units will include a sump where all contaminant will collect 

as it drips from the filter cartridges. A 1-1/2˝ FNPT coupling 

is  welded  into  the  back  side  of  the  sump  allowing  the 

collected contaminant to be reclaimed or drained. 

Blower Cabinet

units  will  have  a  blower  cabinet  where  the  motorized 

impeller style blower is housed, as well as the electrical 

controls.

Summary of Contents for SMOGHOG SHM-05C

































Reviews: