background image

5

● The product, including side rails, must be fully erected prior     

   to use.    

● Strings can cause strangulation! Never place items with a 

   string around a child’s neck such as hood strings or pacifier 

   cords. Never suspend strings over product or attach strings 

   to toys.  

● Discontinue use of the product when child is able to climb 

   out or reaches the height of 35in. (90cm).  

● Child can become entrapped and die when improvised 

   netting or covers are placed on top of a product. Never add 

   such items to confine child in product.  

● When child is able to pull to standing position, set mattress/

   base to lowest adjustment position and remove bumper 

   pads, large toys, and other objects that could serve as steps 

   for climbing out.  

● Never place product near a window where cords from blinds 

   or drapes can strangle a child.  

● Use ONLY mattress/pad provided by manufacturer (which 

   must be at least 53 in. long by 25 in. wide and not more than 

   4 in. thick). 

● Check proper fit of mattress. Should be not more than 4 inches 

   thick. The maximum gap between mattress and inside of crib 

   border (or edge) should be no more than 1 inch.

● Always provide the supervision necessary for the continued 

   safety of your child. When used for playing, never leave 

   child unattended.  

● To reduce the risk of SIDS, pediatricians recommend 

   healthy infants be placed on their back to sleep, unless

   otherwise  advised by your physician.  

● Never use this product if there are any loose or missing 

   fasteners, loose joints, broken parts, or torn mesh/ fabric. 

   Check before assembly and periodically during use. Contact 

   MDB Family for replacement parts. Never substitute parts.  

● Never use plastic shipping bags or other plastic film as 

   mattress covers not sold and intended for that purpose.

    They can cause suffocation. 

● Never use a water mattress with this product.   

● If refinishing, use a nontoxic finish specified for children’s 

   products.

Failure to follow these warnings and the 

instructions could result in serious injury or death.

WARNING:

Summary of Contents for u0400

















Reviews: