background image

Ubee Interactive — www.ubeeinteractive.com 

 

 

 

  Ubee DVW32CB – Safety and Installation Product Insert v1.0 

may be used. 

Devices will not permit operations on channels 
120-132 for 11a and 11n/a which overlap the 
5600 - 5650 MHz band. 

FCC Caution: Any changes or modifications not 
expressly approved by the party responsible for 
compliance could void the user's authority to 
operate this equipment. 

For product available in the USA/Canada market, 
only channel 1 ~ 11 can be operated. Selection 
of other channels is not possible. 

For operation within 5.15 ~ 5.25GHz frequency 
range, it is restricted to indoor environment.   

FCC Radiation Exposure Statement: 

This device complies with FCC radiation 
exposure limits set forth for an uncontrolled 
environment. This device should be installed and 
operated at a minimum distance of 25cm 
between itself and your body. 

This device and it's antennas(s) must not be 
co-located or operating in conjunction with any 
other antenna or transmitter except in 
accordance with FCC multi-transmitter product 
procedures. 

 

Safety Notices   

Read these instructions carefully before 
operating the device. It is important to be aware 
of these safety instructions. Install the device 
according to these instructions and keep this 
guide for future reference. 

1.  Do not use this device in a humid space, in 

the rain, or near splashing water. 

2. Do not install during thunder or lightning 

storms. 

3.  Do not cover any ventilation openings in the 

device case. 

4.  Do not place the device near heat sources 

Summary of Contents for DVW32CB








Reviews: