background image

ES-16-150W

Operating Temperature

-5 to 40° C (23 to 104° F)

Operating Humidity

5 to 95% Noncondensing

Certifications

CE, FCC, IC

Safety Notices

1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.

WARNING:

 Failure to provide proper ventilation may cause fire hazard. Keep at least 20

mm of clearance next to the ventilation holes for adequate airflow.

WARNING:

 To reduce the risk of fire or electric shock, do not expose this product to rain or

moisture.

WARNING:

 Do not use this product in location that can be submerged by water.

WARNING:

 Avoid using this product during an electrical storm. There may be a remote

risk of electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current requirements indicated

on the manufacturer’s label. Connection to a different power source than those specified may
result in improper operation, damage to the equipment or pose a fire hazard if the limitations are
not followed.

2. There are no operator serviceable parts inside this equipment. Service should be provided only

by a qualified service technician.

3. This equipment is provided with a detachable power cord which has an integral safety ground

wire intended for connection to a grounded safety outlet.

a. Do not substitute the power cord with one that is not the provided approved type. Never use

an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding
wire.

b. The equipment requires the use of the ground wire as a part of the safety certification,

modification or misuse can provide a shock hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there are questions about the installation

prior to connecting the equipment.

d. Protective earthing is provided by Listed AC adapter. Building installation shall provide

appropriate short-circuit backup protection.

e. Protective bonding must be installed in accordance with local national wiring rules and

regulations.

Limited Warranty

ui.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,
where applicable, specify arbitration instead of jury trials or class actions.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause

undesired operation.

ES-16-150W Quick Start Guide

Summary of Contents for EdgeSwitch ES-16-150W












Reviews: