background image

d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate

short-circuit backup protection.

e. Protective bonding must be installed in accordance with local national wiring rules and regulations.

Limited Warranty

ui.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where

applicable, specify arbitration instead of jury trials or class actions.

Compliance

FCC

Changes or modi cations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operations of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

ISED Canada

CAN ICES-3(A)/NMB-3(A)

Australia and New Zealand

Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this

equipment may cause radio interference.

CE Marking

CE marking on this product represents the product is in compliance with all directives that are applicable

to it.

WEEE Compliance Statement

Declaration of Conformity

ES-12F Quick Start Guide

×

Click for

Table of Contents

Summary of Contents for EdgeSwitch















Reviews: