background image

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the 
product(s) furnished hereunder (the “Product(s)”) shall be free from defects 
in material and workmanship for a period of one (1) year from the date 
of shipment by UBIQUITI NETWORKS under normal use and operation. 
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under 
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, 
to repair or replace any Product that fails to conform to the above 
warranty during the above warranty period. The expense of removal and 
reinstallation of any Product is not included in this warranty. The warranty 
period of any repaired or replaced Product shall not extend beyond its 
original term. 

Warranty Conditions

The above warranty does not apply if the Product:

(I) 

has been modified and/or altered, or an addition made thereto, 
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized 
representatives, or as approved by Ubiquiti Networks in writing;

(II) 

has been painted, rebranded or physically modified in any way;

(III) 

has been damaged due to errors or defects in cabling;

(IV) 

has been subjected to misuse, abuse, negligence, abnormal 
physical, electromagnetic or electrical stress, including lightning 
strikes, or accident;

(V) 

has been damaged or impaired as a result of using third party 
firmware;

(VI) 

has no original Ubiquiti MAC label, or is missing any other original 
Ubiquiti label(s); or

(VII) 

has not been received by Ubiquiti within 30 days of issuance of 
the RMA.

In addition, the above warranty shall apply only if: the product has been 
properly installed and used at all times in accordance, and in all material 
respects, with the applicable Product documentation; all Ethernet cabling 
runs use CAT5 (or above), and for outdoor installations, shielded Ethernet 
cabling is used, and for indoor installations, indoor cabling requirements 
are followed.

Returns

No Products will be accepted for replacement or repair without obtaining 
a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS 
during the warranty period, and the Products being received at UBIQUITI 
NETWORKS’ facility freight prepaid in accordance with the RMA process of 
UBIQUITI NETWORKS. Products returned without an RMA number will not 
be processed and will be returned freight collect or subject to disposal. 
Information on the RMA process and obtaining an RMA number can be 
found at: www.ubnt.com/support/warranty.

Summary of Contents for RocketDish LW RD-5G30-LW

























Reviews: