background image

Antenna Gain of 4 Single-Polarity Antennas

(2) Dual-Band

2.4 GHz

4.5 dBi

5 GHz

5 dBi

(2) Single-Band

5 GHz

5 dBi

Safety Notices

1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories speci ed by the manufacturer.

WARNING:

 Do not use this product in location that can be submerged by water.

WARNING:

 Avoid using this product during an electrical storm. There may be a remote risk of

electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the

manufacturer’s label. Connection to a different power source than those speci ed may result in

improper operation, damage to the equipment or pose a  re hazard if the limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service should be provided only by a

quali ed service technician.

Limited Warranty

ui.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where

applicable, specify arbitration instead of jury trials or class actions.

Compliance

FCC

Changes or modi cations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

UAP-BeaconHD Quick Start Guide

Summary of Contents for UniFi AP BeaconHD












Reviews: