UDI R/C Discovery2 Operation Manual Download

Page: 24 / 28

www.udirc.com

Spare Parts

For convenience, the spare parts are listed for you to choose, which can be
purchased from the local seller.

U818A Plus-W-01

Drone cover housing

U818A Plus-W-02

Drone bottom housing

U818A Plus-W-03

A Propeller

U818A Plus-W-04

B Propeller

U818A Plus-W-05

Landing Gear

U818A Plus-W-06

Motor cover holder A

U818A Plus-W-07

Motor cover holder B

U818A Plus-W-08

Motor bottom holder

Battery installation diagram

When install, you need to squeeze up and down of
the battery buckle(picture 29) and then put the lipo
battery aim at the drone battery slot, push into the
position is fine.

Receiver board solder wire diagram

Picture 29

Front

Rear

Left front motor negative cable solder pad: blue wire

5P cable socket: Camera adapter board

Left front motor positive cable solder pad: red wire

Left front LED board positive cable solder pad: green wire

Left front LED board negative cable solder pad: black wire

Left rear LED board negative cable solder pad: black wire

Left rear LED board positive cable solder pad: yellow wire

Left rear motor positive cable solder pad: red wire

Left rear motor negative cable solder pad: blue wire

Right front motor negative cable solder pad: blue wire

Right front motor positive cable solder pad: red wire

Right front LED board positive cable solder pad: green wire

Right front LED board negative cable solder pad: black wire

Right rear LED board negative cable solder pad: black wire

Right rear LED board positive cable solder pad: yellow

Right rear motor positive cable solder pad: red wire

Right rear motor negative cable solder pad: blue wire

3P cable socket: power board

Battery adapter board negative cable solder pad: black wire

Battery adapter board positive cable solder pad: red wire

Summary of Contents for Discovery2





























Search results

Summary of Contents for Discovery2

Reviews:

Related manuals for Discovery2

Brands by name

Popular brands

UDI R/C Discovery2, Operation Manual

Search results

Summary of Contents for Discovery2

Reviews:

Related manuals for Discovery2

Brands by name

Popular brands