background image

26

www.udirc.com

Troubleshooting Guide

The
transmitter
indicator
light is off

Fail to pair
the drone
with
transmitter

The drone
is under-
powered
or can not
fly.

The drone
could not
hover and
tilts to one
side.

1

2

3

4

Problem

Problem Cause

Solution

No.

1. Low battery.

1. Replace the transmitter battery.

2. The battery positive pole and negative
    pole are in reverse order.

2. Install the battery in accordance with the
    user manual.

3. Poor Contact.

3. Clean the dirt between the battery and the
    battery slice.

1. Indicator light is off.

1. The same as above 1.2.3.

2. There is interfering signal nearby.

2. Restart the drone and power on the
    transmitter.

3. Misoperation.

3. Operate the drone step by step in
    accordance with the user manual.

4. The electronic component is damaged
    for frequent crash.

4. To buy spare parts from local seller and
    replace damaged parts.

1. The propeller deformed seriously.

1. Replace the propeller.

2. Low battery.

2. Recharge the drone battery.

3. Incorrect installation of propeller.

3. Install the propeller in accordance with
    the user manual.

1. The propeller deformed seriously.

1. Replace propeller.

2. The motor holder deformed.

2. Replace the motor holder.

3. The gyro did not reset after violent crash.

3. Put the drone on the flat ground for about
    10s or restart the drone to calibrate again.

4. The motor is damaged.

4. Replace motor.

The drone
indicator
light is off.

Could not
see the
picture.

Hard to

control by

cellphone.

5

6

7

1. Low battery.

1. Recharge the drone battery.

2. The battery is expired or over discharge
    protection.

2. Buy a new battery from local seller to
    replace the battery.

3. Poor contact.

3. Disconnect the battery and then connect
    it with the plug again.

1. Did not connect the wire of camera box
    or poor contact.

1. Check the wire and connect well.

2. There is interfering signal nearby.

2. Cut off the wire and re-connect.

3. Damaged camera.

3. Buy a new camera box from local seller
    to replace.

1. Not experienced enough.

1. Practice and read the cellphone
    controlling instruction carefully.

Double 

image 

when 

using VR

8

1. Lens focal length is not correct.

1. If there is double image, move the lens to
    the proper position till the image is clear.

Summary of Contents for Discovery2





























Reviews: