background image

                          Turn off the power of the boat 

and fix the drive wheels. Unscrew the anti-skid 

nut counterclockwise and then unscrew the 

propeller.

Disassembly:

Installation:

Low Battery Alarm

Out of Range Alarm

The motor lowers the temperature by flowing water. During the voyage, water flows through the 

heat pipe around the motor, which has a cooling effect on the motor.

Water cooling system

Only when the boat is in the water can it work normally. Stop working after leaving the water surface, 

prevent misoperation and play a role of safety protection.

Out of water protection

Boat:

 When the boat in low battery, the transmitter will beep “di.di.di. ...” constantly to remind the 

           user to remote back the boat as soon as possible. And the boat speed will slow down to half 

           and the capsize reset function will turn off automatically when the boat in low battery.

Transmitter:

 When the transmitter in low battery, the transmitter will beep “di.di.di. ...” to remind 

                        the user to remote back the boat to replace the batteries as soon as possible.

When the boat is running out of the max remote control distance, the transmitter will beep

 “didi...didi...” to alarm the user to remote back the boat immediately.

Anti-skid nut

Drive wheels

                        Fix the rotating wheel first and then tighten 

the new propeller,finally tighten the nuts.

Propeller Replacement

Parts Replacement

Safety Precautions

1) Turn on the transmitter power first and then turn on the boat power before playing; Turn off the boat power first and then 

turn off the transmitter power when finish playing.

2) Make sure the connection is solid between battery and motor etc. The ongoing vibration may cause bad connection of 

power terminal.

3) Improper operation may cause impact to the boat and damage the hull or propeller.

4) It is forbidden to sail in the water where people are useful and sail away from salt water and sundry water.

5) The battery must be take out after playing to keep the cabin dry and clean.

If the boat capsizes, Push forward and 

backward the throttle trigger of the 

transmitter and then pull back at once. 

The boat will then return to normal, the 

capsize reset function will turn off 

automatically when the boat in low battery.

Self-Righting Hull

Motor

06

Summary of Contents for UDI008









Reviews: