background image

Instructions for use (rev 031121) - En 

PROGRAMIX 50 - 100 

 

 

UGIN DENTAIRE 

 

12 

 

 

3

rd

 STAGE 

o

 

Rate No. 3 (RP 3): from 1 to 15°C/min 

 FULL - STOP 

Temperature rise to the 3

rd

 stage. 

 

o

 

3

rd

 stage temperature: from 0 to 1200°C 

Temperature setting for the 3

rd

 stage 

 

o

 

Hold time from 0 to 240 min 

Hold time for the temperature of the 3

rd

 stage. 

 

 

DELAY FINAL: FROM 0 TO 240 MIN 

This timer function sets a time delay before the firing cycle is stopped completely. 
Once you have programmed your full cycle, you may program the furnace hold at the last temperature for 0 
to 240 min, in addition to the hold time. 
This means that you can choose the time you need to perform your castings. 
 

5.5.

 

PROGRAM NUMBER DISPLAY 

If the control station is on stand-by, the program number can be changed using the keys 

 and 

 

The control station has a storage capacity of 30 programs. 

-

 

Programs 0 to 19 are 3-stage programs. 

-

 

Programs 20 to 29 are a double 6-stage programs. 

The program number cannot be changed while the furnace is in operation (the program number blinks, key              

 enabled) or when the cycle has begun (

key enabled). 

 

5.6.

 

TEMPERATURE/TIME DISPLAY 

This display gives you the value of the parameters while setting up the program. During the heating cycle, 
you can choose to display either: 
-

 

the temperature during the heat rise and the countdown during the hold periods, 

-

 

or the temperature only. 

ln that case, press the 

 key. A dot then appears at the far right of the display (No. 3) to indicate that 

you have chosen the temperature mode. 
 

5.7.

 

INDICATOR OF THE UNIT DISPLAYED ON THE PANEL (No. 3) 

Two red lights indicate units of temperature and heating rate: °C and °C /min. Two green lights indicate units 
of time: hours and minutes. 
 

5.8.

 

MODE KEY 

This  key 

  is  pressed  to  switch  from  the  temperature/time  display  mode  to  the  temperature  only 

display mode.  
 
 

5.9.

 

FORWARD AND REVERSE KEY 

ln 

stand-by position

, pressing one of the increment/decrement keys modifies the program number. 

Summary of Contents for PROGRAMIX 100























Reviews: