background image

CX2162/66 

S

ECURITY

 

 

2

 

Security 

2.1

 

Proper use 

The electronic knob cylinder CX216x is intended for installation in building doors 
and for locking and unlocking doors. They need to be equipped with a DIN lock 
for Euro profile cylinders. The CX216x locking cylinder can be used indoors as 
well as outdoors (depending on the product version). 
The assembly should be carried out only by trained technicians. Only the 
components approved by Uhlmann & Zacher should be used for installation and 
maintenance. 
Any other use is considered as improper and may result in damage to material or 
even in physical injury. 

2.2

 

Improper use 

The CX216x should not be used for locking up people or animals as well as 
supplies required in case of emergencies (for example defibrillator, emergency 
medication, fire extinguishers, etc.).  
The CX216x should not be used in potentially explosive surroundings. 
Specially approved versions that are intended for the purpose should be installed 
and used in fire, smoke resistant doors and emergency exit locks. The applicable 
regulations should be followed. 
The CX216x should not be used if the housing or the electronics is damaged. 
Changes or retrofits to the product are not allowed. The knob module should not 
be used outside the given specifications.  
The knob module should not be used in doors that do not open freely or in doors 
or lock cases that are damaged. The door should not be opened using the knob 
module. The knob module should not be used as a stopper against obstacles. 

2.3

 

General safety instructions 

Follow these basic safety instructions when using the knob cylinder: 

 

Installation and battery replacement should only be done by qualified 
technicians according to the instructions in this operating and assembly 
manual. 

 

Do not use the knob cylinder in potentially explosive areas. 

 

Do not make any kind of modifications to the knob cylinder, with the 
exception of those described in this operating and assembly manual. 

 

Do not apply paints or acids to the knob cylinder. 

 

Dot not heat the knob cylinder and battery beyond the specified storage 
temperature. 

 

Use only original spare parts and accessories from Uhlmann & Zacher to 
prevent malfunctions and damages. 

 

Only use batteries procured from Uhlmann & Zacher. 

 

 

Summary of Contents for CX2162



























Reviews: