background image

 

Issue 3: 20/04/20 

                                                                                                                                                           Page 

10

 of 

32 

 

 

Warning:

 

Possible danger to life due to alteration of the patient’s position

 

 

 

Always lock (disable) all handset adjustment functions which could cause danger to 
the patient’s health if adjusted (consult doctor).  

 

Always take account of the patient’s condition when locking (disabling) the 
adjustment options. 

 

Warning:

 

Accident hazard due to falling out of the bed!

 

 

 

The bed should always be left in its lowest position when the patient is unsupervised the bed 

can be adjusted to a suitable height for the patient to get in or out of the bed in order to 

reduce the risk of injury due to falls. 

 

 

 

Caution:

 

Risk of short circuit and fire 

 

 

 

Before moving the bed, disconnect the mains plug and secure the mains cable from being 

run over.  

 

Do not use the bed in surroundings in which flammable gases or vapors (e.g. from 

anaesthetics) may be present. 

 

 

Caution:

 

Danger due to actuator motor overheating! 

 

 

 

Before adjusting the bed height, ensure that nothing is blocking the full adjustment 
movement.  

 

Avoid operating the actuator motors continuously for more than two minutes.  

 

Maximum continuous operation of the actuator motors is 2 minutes; the minimum pause 
after 2 minutes operation is 18 minutes.  

 

Never use more than two actuator motors simultaneously.  

 

Ensure there is nothing preventing the actuator from working correctly, a mattress 
incorrectly secured to the bed frame can prevent the backrest or knee break from 
functioning correctly and causing damage to the patient or the Bed. 

 

5.2  Safety information 

– bed assembly 

 

 

Warning:

 

Risk of Injury due to incorrect assembly!

 

 

  Ensure that all bed components are correctly assembled.  

  Check that all adjustment options are in perfect working order after assembly,  

 

Summary of Contents for Soprano Bariatric

































Reviews: