manualshive.com logo in svg

Ultra-Aire SD12, Installation Instructions Manual

The Ultra-Aire SD12 is a high-quality dehumidifier designed to improve indoor air quality. To ensure hassle-free installation, we provide a detailed Installation Instructions Manual. This comprehensive manual is available for free download at 88.208.23.73:8080, allowing you to easily set up and optimize your SD12 unit.

Share
Download
background image

2

3

Ultra-Aire SD12 Installation Instructions

www.Ultra-Aire.com | (800) 533-7533

www.Ultra-Aire.com | (800) 533-7533

Ultra-Aire SD12 Installation Instructions

Safety Instructions ...................................................................... 3
Specifications .............................................................................. 4
Optional Accessories ................................................................... 5
Dehumidifier Set Up .................................................................... 6
Condensing Unit Set Up ............................................................... 7
Attaching Duct Collars ................................................................. 8
Dehumidifier Electrical Requirements ......................................... 9
Condensing Unit Electrical Requirements ................................. 10
Condensing Unit & Dehumidifier Wiring .................................... 11
Line Set Installation ................................................................... 12

Brazing the Line Set .......................................................................14-15
Leak Test Line Set and Dehumidifier ................................................... 16
Evacuating the Line Set and the Dehumidifier .................................... 17
Charging the System ........................................................................... 18

Drain Installation ....................................................................... 19
Ducting to HVAC Systems .......................................................... 20  

Recommended HVAC System Installations ........................................ 21
Alternative HVAC System Installations ................................................ 22
Recommended Multiple HVAC Systems Installation .......................... 23
No Existing Ductwork Installation ....................................................... 24

Fresh Air Ventilation .................................................................. 25

Determine Ventilation Requirements ................................................... 26

Controls ..................................................................................... 27

Wiring Controls .................................................................................... 28

Air Filtration ............................................................................... 29

MERV Rating Chart ............................................................................. 30

Service ....................................................................................... 31

Troubleshooting ................................................................................... 32

Warranty .................................................................................... 35

TABLE OF CONTENTS

Ultra-Aire is committed to manufacturing quality products. To maintain  

our standards, product specifications may change without notice. 

4201 Lien Road, Madison, WI 53704 

(800) 533-7533 

www.Thermastor.com  |  www.Ultra-Aire.com

© 2015 Therma-Stor LLC

Summary of Contents for SD12





































Reviews:

No comments

Related manuals for SD12

Guardian H965 Use & Care Instructions Manual preview
H965
Brand: Guardian Pages: 12
Novita Humiperfect NH890 Operating Instructions And E-Warranty Application preview
Humiperfect NH890
Brand: Novita Pages: 19
Westinghouse WHD-120 User Manual preview
WHD-120
Brand: Westinghouse Pages: 10
Qlima D 109 Operating Manual preview
D 109
Brand: Qlima Pages: 128
Essick Bemis 527 300 Owner'S Care & Use Manual preview
Bemis 527 300
Brand: Essick Pages: 32
AEG LAVATHERM T37840 Operating Instructions Manual preview
LAVATHERM T37840
Brand: AEG Pages: 125
AEG LAVETHERM 610 Operating Instructions Manual preview
LAVETHERM 610
Brand: AEG Pages: 16
AEG lavaterm 620 Operating Instructions Manual preview
lavaterm 620
Brand: AEG Pages: 12
AEG LAVATHERM 3400 Operating Instructions Manual preview
LAVATHERM 3400
Brand: AEG Pages: 28
Hunter 33223 User Manual preview
33223
Brand: Hunter Pages: 21
Hyundai HUM 2005 Instruction Manual preview
HUM 2005
Brand: Hyundai Pages: 20
Hyundai HUM 770 Instruction Manual preview
HUM 770
Brand: Hyundai Pages: 40
Hyundai H-HU4.3-U11E Instruction Manual preview
H-HU4.3-U11E
Brand: Hyundai Pages: 36
Lanaform VAPOLUX Manual preview
VAPOLUX
Brand: Lanaform Pages: 96
Zodiac SIROCCO2 Instruction Manual preview
SIROCCO2
Brand: Zodiac Pages: 10
Legend Brands 103806 (F515) Owner'S Manual preview
103806 (F515)
Brand: Legend Brands Pages: 19
EcoSeb DD122EA CLASSIC Instructions Manual preview
DD122EA CLASSIC
Brand: EcoSeb Pages: 10
EcoSeb DD322EA CLASSIC Manual preview
DD322EA CLASSIC
Brand: EcoSeb Pages: 10

Brands by name

Popular brands

Load more brands