background image

Please take time to read the following safety operating instructions.  They are the key to the 
successful operation of your Ultra-Max Conveyor Oven.

To adjust the time and temperature:

1.  Press the DOWN and UP arrows (

) at 

the same time.  Hold for four seconds until 
the TEMPERATURE display goes blank.

2.  Press the ENTER button (

) to switch 

between TIME and TEMPERATURE.

3.  Press the UP arrow (

) to increase or the 

DOWN arrow (

) to decrease the TIME or 

TEMPERATURE.  Hold either button down 
for faster display changes.

4.  After fi ve seconds, the new numbers will 

be saved and the oven will display the new 
settings.

To turn the oven off:

1.  Push the power switch to "OFF."  The 

oven is equipped with a cool-down feature 
for motor shaft and bearing protection. 

 

This enables the blower motor(s) to run 
regardless of the controller status.  The 
blower(s) continue to run until the oven 
cools to a safe temperature.

3) Press the up button (

) to increase 

or the down button (

) to decrease 

TIME or TEMPERATURE.  Hold 

button down for faster display 
changes.

4) After five seconds, the new numbers 
will be saved and the oven will display 

new settings.

4) Après cinq secondes, les nouveaux 

nombres seront sauvés et le four montrera 
de nouveaux arrangements.

3) Tenez "vers le haut" bouton  (

)  pour 

augmenter ou "vers le bas" boutonnez  (

pour diminution de le TEMPS ou 

TEMPÉRATURE.  Maintenez le bouton pour 
des changements plus rapides. 

A Star Manufacturing Company

2) Press the enter button (     ) to 
switch between TIME and 
TEMPERATURE.

Push power switch "ON." 

To Start:   

2) Appuyez sur le bouton de "entrée" (     ) 
pour commuter entre le TEMPS et la 

TEMPÉRATURE. 

1) Tenez "vers le haut" et "vers le bas" 

boutonne  (

)  en même temps. Tenez 

les boutons pendant quatre secondes 

jusqu'à ce que l'affichage de la 

TEMPS soit blanc. 

Après cinq minutes, nouvelle tentative. 

Si le brûleur n'allume pas en une minute, 
poussée le commutateur de puissance dans 

la position de "ARRÊTE" et attend 5 minutes. 

Poussez le commutateur de puissance à 
"MARCHE."

OFF / ARRÊTE

Ajustement du TEMPS et de la 

TEMPÉRATURE:

Pour Commencer:

ON / MARCHE

“HEAT” LIGHT

“TIME” LIGHT

If burner does not light in one minute 
push the power switch to the "OFF" 
position and wait five minutes. 

1) Press the up and down buttons 

) at the same time, hold for four 

seconds until TIME display is blank.

Adjusting TIME and TEMPERATURE:

After five minutes, retry.  

SAFETY TIPS

For your safety, read before operating.

If you smell gas:

1.  DO NOT try to light any appliance.
2.  DO NOT touch any electrical switches.
3.  Use an exterior phone to call your gas 

supplier immediately.

4.  If you cannot reach your gas supplier, call 

the fi re department.

In the event of a power failure:

1.  Turn all switches off.
2.  DO NOT attempt to operate the oven until 

the power is restored.

General Safety Tips:

1.  If the oven needs to be moved for any 

reason, the power must be disconnected 
from the unit before doing so.  

2.  DO NOT remove the control box cover 

unless the oven is unplugged.

OPERATION

To turn the oven on:
1.  Push the power switch to "ON."
2.  After the fan begins to build pressure, 

the pressure switch will provide power to 
the control board to engage the heating 
element contactor.  You should hear an 
initial "click" from the contactor as it begins 
to heat.

Summary of Contents for 8B-UM1833





































Reviews: