Ultra Start 3295 SERIES Installation Manual Download

Page: 7 / 32

SYSTEM PROGRAMMING -

Menu 1

PAGE 6

95 SERIES

INSTALL MANUAL

QUICK VIEW PROGRAMMING

Press Lock

Press Unlock

Press Start

Press Status

MENU 1

MENU 2

MENU 3

MENU 4

1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and release the Program Switch 1 time. (Horn/ Siren will chip to confirm program
mode entered)
3 - Select the Program Menu by pressing...

ENTERING PROGRAM MODE

1 -

Cycle the Ignition Key On/Off On/Off On (

Leaving the key ON

)

2 -

Press and

RELEASE

the Program Switch 1 time.

(Horn/ Siren will chip to confirm program mode has been entered)

3 -

Press and

HOLD

the Program Switch for 5 seconds or until the Horn/ Siren Chirps 3 times.

4 - Turn the ignition key

OFF

to exit.

SYSTEM RESET

TRANSMITTER PROGRAMMING

1 -

Cycle the Ignition Key On/Off On/Off On

(Leaving the key ON)

Press and

HOLD

the Program Switch

(The Horn/ Siren will chirp 1 time,

CONTINUE to HOLD)

**If the Horn/ Siren does not chirp turn the key off, then repeat step 1**

Continue to

HOLD

the Program Switch and the Horn/ Siren will chirp 5 times.

Press the

LOCK BUTTON

on each of the remote’s to be programmed.

*Pause for about 1 second between programming of each remote

System can accept up to a maximum of 4 remote’s

The park lights will flash once and the Horn/ Siren will chirp once each time a new code is

learned.

Release the Program switch and turn Ignition OFF.

4 - Press and Release the Program Switch to advance through the settings.

(

Confirmed by Horn/ Siren chirps & LED flashes)

5 - Press and hold the Program Switch to change the setting

(Confirmed by Horn/ Siren Chirps)

6 -

To exit Program Mode, turn the key off.

(Confirmed by Long Horn/ Siren Chirp)

SYSTEM PROGRAMMING -

Menu 1

PAGE 7

95 SERIES

INSTALL MANUAL

QUICK VIEW PROGRAMMING

IGNITION AUTO-LOCKS

DISABLED

SETTING #

LED FLASHES

SETTING

DESCRIPTION

OPTION 1

1 CHIRP

OPTION 2
2 CHIRPS

OPTION 3
3 CHIRPS

IGNITION

AUTO-LOCK

IGNITION AUTO-LOCK /

UNLOCK

IGNITION AUTO-LOCK

ONLY

HORN / SIREN

SETTINGS

HORN / SIREN CHIRPS

DISABLED

HORN/SIREN CHIRPS

ENABLED

DOOR LOCK PULSE

OPTIONS

DOUBLE UNLOCK &

SINGLE LOCK

DOUBLE LOCK & SINGLE

UNLOCK

SINGLE LOCK & SINGLE

UNLOCK

DOOR LOCK / UNLOCK

PULSES

0.25 SEC PULSES

3 SEC PULSES

0.75 SEC PULSES

AUX CHANNEL 1

(-) IGNITION

2ND UNLOCK

DOME LIGHT

(-) ACCESSORY OUTPUT

# AUX 1 OUTPUT

WITH DISARM

AUX CHANNEL 2

AUX OUTPUT (UNLOCK &

STATUS) WITH DISARM

PASSIVE DOOR LOCKS

DISABLED

PASSIVE DOOR LOCKS

ENABLED

PASSIVE ARMING/

PASSIVE ST. KILL

FULL PASSIVE ARMING

ENABLED

PASSIVE SAFETY REARM

ENABLED

ALARM

SHOCK / AUX SENSOR

INTERNAL SHOCK

DISABLED

AUX SENSOR DISABLED

BOTH SENSORS ENABLED

ACTIVE ARMING ONLY

PROGRAM MODE 1

SETTING #

LED

FLASHES

SETTING

DESCRIPTION

OPTION 1

1 CHIRP

OPTION 2
2 CHIRPS

OPTION 3
3 CHIRPS

ALARM

VALET SETTINGS

SECURE VALET

15 SECONDS

STANDARD VALET

PARK-LIGHT OUTPUT

30 SECONDS ON DISARM

NORMAL OPERATION

HORN TIMING

5MS OUTPUT

50MS OUTPUT

10MS OUTPUT

* 30ms ON ALARM

SIREN OPTIONS

30 SECOND DURATION

PULSED FOR HORN

60 SECOND DURATION

PROGRAM MODE 2

PROGRAM MODE 1 - see page 16 for detailed instructions

PROGRAM MODE 2 - see page 19 for detailed instructions

SYSTEM PROGRAMMING -

Menu 1

SYSTEM PROGRAMMING -

Menu 1

Summary of Contents for 3295 SERIES

































Search results

Summary of Contents for 3295 SERIES

Reviews:

Related manuals for 3295 SERIES

Brands by name

Popular brands

Ultra Start 3295 SERIES, Installation Manual

Search results

Summary of Contents for 3295 SERIES

Reviews:

Related manuals for 3295 SERIES

Brands by name

Popular brands