background image

Remote Control Mode For Vehicles           

Page 8

Battery Replacement

Change the battery when the Low battery icon is displayed on the LCD screen.
Replace with Lithium 

CR2032 Battery.

*To avoid possible water  damage, have the battery changed professionally. 

Caution

DO NOT DISASSEMBLE THIS WATCH FOR ANY OTHER REASON THEN TO 
REPLACE THE BATTERY. REMOVING ANY OTHER COMPONENT(S) WILL

VOID THE WARRANTY

.

 

Arm/ Lock

- Press and release.

Panic Mode

- Press and hold for

2 seconds.

Disarm/ Unlock

- Press and release

Trunk Release

- Press and hold for 

2 seconds.

 

 

Button 1

Light Button 

Button 2

Remote Start

- Press and release

Remote Stop

- Press and hold for

2 seconds.

Program Start On

MODE Button

Light Button

Button 1

Low Battery

ST.STP Button

Alarm On

Reset Button

Button 2

This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance voids the
 users authority to operate this device.

FCC Notice

Summary of Contents for 7









Reviews: