background image

PAGE 16

72 SERIES

OWNER'S  MANUAL

LED 2 WAY

LED 2 WAY SYSTEMS

PANIC MODE

When the lock button is held for 5 seconds the system will enter Panic Mode. 
The LEDs under the buttons will flash in a pattern and the remote will beep to 
indicate Panic Mode is active. If the system is not in range the remote will 
beep 3 times.

LOCK

UNLOCK

TRUNK RELEASE

When the unlock button is held the light behind the button will flash twice and 
the remote will beep twice after 3 seconds the remote with beep again as 
confirmation that the function has been completed. If the system is not in 
range the remote will beep 3 times.

LOW

BATTERY

LOW BATTERY WARNING

When the battery voltage is low all of the LEDs behind the buttons will 
activate at the same time and the remote will beeps once immediately when 
a button is pressed. Range and features such as Panic Mode and Trunk 
Release may not function when the batteries are low.

HOLD

HOLD

COLD START MODE 

(See page 13 for more details)

1- Press and release the # button then within 3 seconds hold the start button for 8 seconds.
2- All 4 LEDs on the remote will illuminate to indicate that the start cycle selection. Within 3 
seconds select the start cycle
a. Press Unlock for 2hr timer. LEDs will flash twice as confirmation. 
b. Press Start for 3hr timer. LEDs will flash three times as confirmation. 
c. Press #  for 4hr timer. LEDs will flash four times as confirmation. 

PRESS AND 
RELEASE

PRESS AND 
HOLD

THEN

 
HOLD 8 SEC.

PAGE 17

OWNER'S MANUAL

TROUBLE SHOOTING

72 SERIES

Vehicle is not remote  
starting?

- Count the park light flashes then see the diagnostics page.
- Check battery voltage in the remote.
- Make sure you are with-in operating range.
- Check if the vehicle anti-theft is activating. 
- Reprogram the remote’s using Transmitter Program Mode.

Doors do not lock
Or unlock

- Was this optional feature installed?
- Have your installer check the door lock connector.
- Have bypass or keyless module reprogrammed.

SYMPTOM                  CAUSE/SOLUTION

Horn does not honk

- Was this optional feature installed?
- Try panic mode to see if horn activates. If not,
  have the systems horn output checked.

Vehicle starts then shuts 
off by itself

- Check if the vehicle anti-theft is activating.
- Is the starter motor staying on to log? If so,
  reprogram the tach and try again.
- See dealer if problem is not resolved.

Lights on the antenna 
are flashing

- When the doors are locked by the remote the LEDs will flash until the 
unlock button is pressed.
- If you do not want the LEDs to flash have your installer program the 
LED flashes off.

The system does not 
respond to the remote 
transmitter

- Try your second remote.
- Check the batteries in the remote.
  Reprogram the remote’s using Transmitter Program Mode.
- Make sure you are with-in operating range.

We recommend that you contact your dealer if you encounter a problem with your system. If your 
dealer is not available, see 

 to locate an Authorized 

Dealer in your area. For more advanced trouble shooting tips, programming videos, programming 
PDF’s and FAQ’s please  visit 

http://ultrastarters.com/dealer_locator.html

www.ultrastarters.com/support.html

PLEASE NOTE

Summary of Contents for 72 SERIES 1272





















Reviews: