background image

13

15

14

12

Fig. 22

Fig. 23

** If the chronograph is not reset (i.e. still running or stopped),

 it will not be 

possible to print and the display will show 

PRINT 0

, there will not be any action 

upon pressing A or B.

** Do not leave the printer on if not in use

 as that drains a higher power from 

the battery.

**  If  the  above  process  is  wrongly  done  with  the  display  switched  to 

UPLOAD ALL, the display will be freezed until the printer is switched off.

UPLOAD MODE

  

The 

PRINTER

 must be switched 

OFF

 in 

UPLOAD MODE

.

In Fig. 20 press D button once will switch to 

UPLOAD ALL

 mode as shown in 

Fig.22.  Pressing A button will 

UPLOAD ALL

 recorded memories to computer (if 

computer is connected).  When the stopwatch is in the process of uploading, an 

indicator  moves  from  right  to  left.  When  upload  is  complete 

UPLOAD  END

  is 

displayed. Press D button to return to 

PRINT MODE

.

Fig. 18

** 

BASE 3 STROKE/FREQ

 -- if the distance is set to 180 and time unit to

seconds, the speed reading for 3 strokes gives the number of strokes / minute.
** 

MEMORY USED UP

-- When all the memories have been used the 4 digit 

LAP

  

counter at the top left corner will start blinking to indicate all memories have been  

used up.  All further 

LAP

 memories will not be recorded in the memory unless  

some memories are cleared as previously indicated.  When there is no memory  

left pressing A to start a race will sound 3 short beeps.

** Do not leave the stopwatch running if not in use

 as that drains a higher 

power from the battery.

TIMER OPERATION

Press C button until the stopwatch goes to the 

TIMER

 mode. The display is as 

shown in Fig.18. The top row is the display for the 1st timer and the middle row is 

the display for the 2nd timer.

Fig. 19

Press and hold B button for 2 seconds will go into the 

SET TIMER

 mode with 

the hour digit of the 1st timer blinking.  Press A button to set to desired hour for 

countdown.  Press B to go to the first digit in minutes and press A to set minutes. 

Similarly by using B and A buttons the desired countdown times for the 1st and 

2nd timers can be set. 

**Pressing C button once any time during this 

TIMER

 setting sequence will 

complete the setting and the timer is ready to start upon pressing the A button.

Press A to start countdown with the “1 ” at the top right corner blinking and the 

timer setting counting down. When the 1st timer approaches zero, the timer 

gives 4 beeps and the 2nd timer starts counting down immediately. When the 

2nd timer approaches zero, it gives 2 beeps and the 4 digit counter at the lowest 

row advances by 1 automatically. At any time during countdown pressing A will 

stop counting.

** If only the 1st timer is set the timer is used as an ordinary countdown timer

   and will give 5 times 4 beeps when the set time is up. The 4 digit counter also  

   advances by 1 automatically when the timer reaches zero.

Fig. 21

Fig. 20

PRINT MODE

 

Press C button to go to the 

PRINT ALL

 mode as 

shown in Fig.20.  Pressing A button will print all 

recorded  memories  (when  the  printer  is  on). 

When the stopwatch is in the process of printing, 

an  indicator  moves  from  right  to  left.  When  

printing is complete 

PRINT END

 is displayed.

Pressing B at the 

PRINT ALL

 mode will go to

the 

PRINT RACE

 mode with display as shown

in Fig.21.
Pressing  A  in  this  mode  will  only  print  the    

memories in this race. Press B to select particular 

race  to  print.  Pressing  C  any  time  during  this 

printing process will stop printing immediately.

** 

Slide  the 

PRINT  MODE  SWITCH

  to  the 

TOP

  position.  Only  the 

SPLIT

  or 

SPEED

 (depending on whether the stopwatch is in 

CHRONO

 or 

SPEED

 mode) 

will be printed. If this switch is slide to the 

DOWN

 position, both 

LAP

 and 

SPLIT 

or 

LAP

 and 

SPEED

 will be printed. (In 

SPEED

 mode, if B is pressed while the 

previous record is still being printed, that 

SPEED

 record cannot be printed in real 

time. The memories still record the full data for recall or upload).

Summary of Contents for 498









Reviews: