background image

04

4.PHOTOMETRICS DIAGRAM

Ÿ

PROFILE is an LED projector,with adjustable shutter,adjustable system and focus.

Ÿ

Do not switch the appliance on if there is a serious temperature difference such as 
after transportation

Ÿ

because it could damage the light due to changes in the environment. So be sure to 
use the appliance until it is at normal temperature.

Ÿ

This light should be far from strong shaking during any transport or movement.

Ÿ

Do not expose the appliance to overheating, humidity or the environment with too 
much dust during installation. IS do not lay power cables on the floor. Or it may 
cause an electronic shock to people. Make sure the installation location is in a safe 
condition before installing the equipment.

Ÿ

Make sure to put the safety chain in place and check if the screws are screwed 
correctly during device installation.

Ÿ

Ensure that the appliance is operated by qualified personnel who know the 
appliance before use.

Ÿ

Keep the original packaging if a second shipment is required.

Ÿ

Do not try to change the projectors without any instruction from the manufacturer or 
repair appointed agencies.

Ÿ

It is not in the warranty interval if there are malfunctions not to follow the user 
manual to operate or any illegal operation, such as short circuit, electronic shock, 
broken lamp, etc.

SPOT 

 WHITE

FRESNEL

PC

 

 

 

 

 

 

 

 

 

 

Lux center

   

Diameter cm.

         

 

 

 

 

 

 

 

 

 

 

Lux center

   

Diameter cm.

         

 11463 

2865 

1273 

716 

458

 

 

 

 

 

 

36 

72 

108 

144 

180

 

 

 

 

 

Beam angle 8°

Lux center

   

Diameter cm.

         

Lux center

   

Diameter cm.

         

 

1757

 

439 

195 

109 

70

 

 

 

 

 

 

228 

456 

684 

912 

1140

 

 

 

 

 

Beam angle 49°

mt 5

mt 2.5

Beam angle 8°

Beam angle 49°

mt 7.5

mt 10

mt 12.5

 

 

 

 

 

 

 

 

 

 

Lux center

   

Diameter cm.

         

 

 

 

 

 

 

 

 

 

 

Lux center

   

Diameter cm.

         

 10517 

2619 

1168 

657 

420

 

 

 

 

 

 

36 

72  

108  

144 

180

 

 

 

 

 

Beam angle 8°

Lux center

   

Diameter cm.

         

Lux center

   

Diameter cm.

         

  1222 

305 

124 

76 

48

 

 

 

 

 

 

239 

477 

716 

954 

1190

 

 

 

 

 

Beam angle 51°

mt 5

mt 2.5

Beam angle 8°

Beam angle 51°

mt 7.5

mt 10

mt 12.5

Summary of Contents for SMART SPOT100 Series













Reviews: