INSTALLATION
FUSE REPLACEMENT
LINKING ADDITIONAL
ROPE LIGHTS
WARNING
1. DO NOT MOUNT OR SUPPORT FLEXIBLE LIGHT IN A MANNER THAT CAN
DAMAGE THE OUTER JACKER OR CORD INSULATION.
2.
RISK OF FIRE AND ELECTRIC SHOCK
. UNCOIL FLEXIBLE LIGHT PRIOR TO
PLUGGING IN. DO NOT USE WITH EXTENSION CORD NEAR WATER MAY
ACCUMLATE. FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
3. MATERIAL MAY BECOME BRITTLE WHEN COLD. DO NOT INSTALL WHERE
IT MAY BE STEPPED ON OR SUBJECT TO PHYSICAL DAMAGE.
4. DO NOT INSTALL NEAR FLAMMABLE LIQUIDS.
5. DO NOT INSTALL CLOSER THAN 3 METERS FROM A SWIMMING POOL
SURFACE.
6. ALWAYS UNPLUG THIS PRODUCT BEFORE INSTALLING OR REPLACING
FUSES. USE ONLY 125-VOLT, 3 AMP MAX.
7. DO NOT COVER FLEXIBLE LIGHT AS THE COVERING MAY CAUSE THE
FLEXIBLE LIGHT TO OVERHEAT AND MELT OR IGNITE.
8. TO PREVENT OVERHEATING, DO NOT ALLOW CONTACT BETWEEN
FLEXIBLE LIGHT CABLES OR PARTS OF THE FLEXIBLE LIGHT CABLE.
MAINTAIN AT LEASE 10MM (0.39IN) SPACING BETWEEN LIGHT CABLE OR
LIGHT CABLE PARTS.
9. NOT SUITABLE FOR FIELD CUTTING OR SPLICING.
10. DO NOT OVERLOAD. DO NOT CONNECT TOGETHER MORE THAN 150
TOTAL FEET.
THANK YOU FOR YOUR PURCHASE!
Like our product?
Leave a review on your favorite
retailer website or amazon.com
Having problems?
Let us know how we can help.
Call 1-800-654-8483 between
7AM-8PM, M-F, Central Time.
For deals, to register your
purchase and to tell us how
we’re doing, simply scan the
code or visit
byjasco.com/deals
Read instructions or watch
easy-to-follow video.
Discover more
innovative lighting at
byjasco.com/lighting
Instructions
made easy
Scan code or visit
byjasco.com/54503i
User Manual
LED Rope Light
Congratulations on your new
UltraPro Escape
LED Rope Light
! Please read this user manual
carefully before using the product. Important
features and operating procedures are
included in this guide. Please keep the manual
in a safe place for future reference.
IMPORTANT:
Before installation, please read all the
warning statements included at the bottom of these
instructions. Save these instructions for later use.
INCLUDED HARDWARE
TOOLS REQUIRED
MOUNTING THE ROPE LIGHT
A - LED rope light with
power cord x 1
B - Mounting clip x 15
Phillips screwdriver
Power drill (optional)
C - Mounting screw x 15
Before installing, make sure that the surface can support the rope
light and that the power cord will be in range of an outlet.
1. Mark the location for each clip (B) and drill pilot holes
using a 1/16in. drill bit.
2. Place the mounting clips over the pilot holes and use a
screwdriver to install and tighten each screw (C).
3. Carefully affix the rope light (A) to each installed clip.
4. Insert the power plug into outlet.
This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Also unplug any additional
strings or products that may be attached to the product. Replace
the fuse as per the user servicing instructions (follow product
marking for proper fuse rating) and check the product. If the
replacement fuse blows, a short-circuit may be present and the
product should be discarded.
1. Grasp plug (1) and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord. Always unplug this
product before installing or replacing fuses.
2. Slide open the fuse access cover (2) on top of the attachment
plug towards blades (3).
3. Remove fuse (4) carefully. Push the fuse from the other side.
4. Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse
(provided with product).
5. Close fuse cover (2). Close the fuse access cover on top of
attachment plug.
6. Risk of fire. Do not replace attachment plug as it contains a
safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
IMPORTANT
: Disconnect the rope light from power before
linking any additional strands. You can link up to three
strands together in a sequence (maximum 150 ft.).
1. Unscrew and remove the end plug (A) to expose the
female connector (B).
2. Make sure the ring gasket (C) is in place on the female
connector.
3. Plug male connector (D) from next segment into
the female connector. Screw compression nut (E) over
connection until tight.
1
1
2
2
4
3
1
1
2
2
3
3
4
5
6
A
B
C
D
E
MADE IN CAMBODIA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited
warranty. Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483 between 7AM—8PM , M-F,
Central Time.
©JASCO 2020 | 54503, 54504, 54505, 54842,
54843, 54586 | 08/06/20 v1
5017247
Intertek
