background image

www.ultratecfx.com

4

Fog Burst Setup

The compressed gas does not have to be air, you can use nitrogen or CO2 gas. CO2 
is liquid in the tank so you can get a large volume from a small tank and regulator. A 
pressure regulator to drop the pressure is required. The number of cycles would 
depend on the volume of your tank. We offer a regulator and hose accessory to 
facilitate this. (see below).

CXP-1968 CO2 Regulator with 5 foot hose & High flow quick disconnect.

This unit is used to supply regulated CO2 gas to run devices that require a source of 
compressed gas.  Shown here on a 5 pound CO2 tank, 

(tank is not included.)

To connect the Fog Burst to the Power Fog Industrial.

1) Remove the 4" ducting adapter from the front/side of the Power Fog Industrial /9D (if 
equipped) 

2) Position the Fog Burst on front of the Power Fog Industrial with the valve assembly 
facing upwards.

3)  Line up the three holes on the mounting bracket with the three mounting holes around 
output nozzle of the fog machine. 

4)Install with the self tapping screws provided with the Fog Burst

5) Connect your compressed gas source to the valve (remember to use a gas pressure 
regulator if your source gas pressure is greater than 100 PSI).

6) Connect the power cord from the Fog Burst to the Auxiliary port on the back of the 
Power Fog Industrial/9D.

 

Compressed Gases

Operating Procedure

 

Optional Timer/ Duration Remote Operation

The Timer/ Duration Remote offers Duration, Interval, Variflow and fog 
on/ off controls.

Timer/ Duration Remote LED Indicator

The Timer/ Duration Remote Handset was designed to indicate 
operation modes. These are as follows:

Slow Flashing Light:

 Indicates unit is not ready to operate but still in 

heating mode, fog is not available at this point.

Quick Flashing Light:

 Indicates unit is ready to operate but still in 

heating mode, some fog is available at this point.

Solid Light:

 Indicates that the unit is ready to fog at full output.

Triple Pattern Flashing Light:

 Indicates that the unit is in an over 

temperature condition and has shut down.

DURATION

INTERVAL

FOG

VARIFLOW

Smoke OFF/ON Switch

Flow Dial

Duration Dial

Interval Dial

Optional Timer/ Duration Remote

LED

Summary of Contents for CLF-4455












Reviews: