background image

RF POWER SUPPLY and MATCHINGBOX

 

5. Operation methods 

 

13 

5.  Operation  methods 

This section explains the operation methods. 

5-1. Switching on the power supply 

 

If  the  POWER  switch  is  set  to  ON,  the  following  screen  appears,  and  settings  can  be 

configured.  If  the  screen  appears  after  the  POWER  switch  is  set  to  ON,  output  starts 

automatically in accordance with the setting values of the screen display. (*Because output is 

not stable until the charging of the electrolytic condenser is complete just after the POWER 

switch is set to ON, wait 5 seconds, and then carry out the necessary operations.)   

 

 

 

 

 

 

To change the parameters, press the ENT key to make the display items flash. 

 

Next, press the NEXT key to select the item to be configured. 

 

Next, press the INC or DEC key to change the parameter. 

 

5-2. Screen 1 

 

At Screen 1, the phase settings for the standard waveform can be configured from 0.0° 

to 359.9° for each channel from P01(CH1) to P04(CH04). 

 

 

 

 

Table 5-1 Explanation of functions of Screen 1 

Category 

Function 

P01 

Adjust the phase of the waveform output from OSC1. 

Configurable from 0.0° to 359.9°. 

P02 

Adjust the phase of the waveform output from OSC2. 

Configurable from 0.0° to 359.9°. 

P03 

Adjust the phase of the waveform output from OSC3. 

Configurable from 0.0° to 359.9°. 

P04 

Adjust the phase of the waveform output from OSC4. 

Configurable from 0.0° to 359.9°. 

P01= 

0.0 

P02=   

0.0 

P03= 

0.0 

P04= 

0.0 

Figure 5-1 Screen 1 (default screen) 

P01= 

0.0 

P02=   

0.0 

P03= 

0.0 

P04= 

0.0 

Figure 5-2 Screen 1 

Summary of Contents for PHS-04N






























Reviews: