MODEL A13A11Z25-12G32L
BALLOON
PART
DESCRIPTION
1
10224
FLANGED MAIN BODY / COFFERDAM
2
10003
GLASS RETAINING RING
3
10219
PROJECTOR MOUNT
4
10220
LENSE HOLDER
5
10006
COMPRESSION RING
6
10007
LOCKING RING
7
10010
GLASS
8
10011
GLASS GASKET
9
10012
CONNECTING RING GASKET
10
10218
PROJECTOR LID
11
10208
RECEPTACLE ASSEMBLY, 2-WAY
12
10209
PLUG ASSEMBLY, 2-WAY
13
10212
LED ARRAY
14
10222
THERMOSWITCH
15
10205
CABLE STRAIN RELIEF
16
10206
ELECTRICAL CABLE
17
10221
LENSE
18
10020
M6 x 1.0 x 14LG SST SHCS
19
10033
M4 x 0.7 x 6LG SST PPHS
20
10044
M4 x 0.7 x 10LG SST SET SCREW
21
10207
M3 x 0.5 x 5LG SST PPHS
22
10211
M3 x 0.5 x 12LG SST SHCS
23
10223
M4 x 0.7 x 8LG SST PPHS
Installation:
The SV10 LED underwater light should be installed by qualified personnel only. It is recommended to mount the light assembly at a minimum of
250-300mm (10-12”) below the light load water line using proper tools and materials. The minimum hull thickness is 10mm (0.4”) and maximum
(for sufficient heat dissipation) is 90mm (3.5”) with an access area of at least 75mm (3”) left behind the light for lamp servicing and general
ventilation.
After selecting the desired location on a flat surface, cut a 100mm (4”) diameter hole through the vessel hull in the desired location. Caution!
Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole location. Note: In order to allow proper
heat dissipation from the installed lights it is important to ensure that any hull insulation/cladding is not in contact with the thru hull or light body.
It is recommended that a minimum of 30mm (1.2”) of clear space should be surrounding the fixture to allow for adequate cooling.
The SV10 must be partially disassembled prior to installation. For light disassembly, disconnect Receptacle (11) from Plug (12), unscrew Projector
Lid (10) from Flanged Main Body (1), remove Locking Ring (6) and Compression Ring (5) from Flanged Main Body (1). Carefully coat Flanged Main
Body (1) and inner surface of hull hole with 3M 5200 Marine Adhesive or equivalent. Caution! Avoid placing excess adhesive on Flanged Main Body
(1) threads. Note: Exposed inner hole surface must be properly sealed before light installation to prevent potential water intrusion into the hull
proper. Holding the Flanged Main Body (1), push the light through the hole, slide Compression Ring (5) over Flanged Main Body (1) and then
tighten Locking Ring (6) hand tight. Note: Ensure that the tips of all six fasteners (18) are NOT touching Compression Ring (5). After the 3M 5200
Marine Adhesive is fully cured, tighten the six fasteners (18) to 9 Nm (7 ft/lbs) using a 5mm allen wrench. The thru hull fitting should be
electrically connected to the vessels cathodic protection system using fastener (19) located on Locking Ring (6). Also, tighten set screw (20)
located in Locking Ring (6) to ensure good electrical continuity to Flanged Main Body (1).
Upon making proper electrical connections (see driver box manual), reverse aforementioned light disassembly procedure and hand tighten
Projector Lid (10). Note: Apply anti-seize compound to Projector Lid (10) internal threads. Upon completing light installation, it is highly
recommended that Flanged Main Body (1) face be coated with antifouling paint. Also, hand tighten 4mm set screw (20) located in Locking Ring (6).
Serviceable Parts:
The SV10 LED Underwater Light is fully serviceable and all parts are replaceable. Please contact our technical support staff to discuss your
individual needs.
For Glass (7) replacement disconnect Receptacle (11) from Plug (12), unscrew Projector Lid (10) from Flanged Main Body (1), remove Glass
Retaining Ring (2) by removing the six fasteners (18) and remove Glass Gaskets (8). Upon thoroughly cleaning all surfaces, reverse said procedure
to reassemble and hand tighten Projector Lid (10). Note: Six fasteners (18) are tightened in a criss-cross pattern to 9 Nm (7 ft/lbs) using a 5mm
allen wrench.
Caution! Never attempt to remove/replace glass while vessel is in the water.
Underwater Lights USA, LLC
Underwater Lights Europe Sarl
3406 S.W. 26
th
Terrace, C 6/7
16, rue Rouaze
Fort Lauderdale, FL 33312 USA
06400 Cannes, France
Phone: 1-954-760-4447
Phone: 33-(0)-4-97-21-02-96
Fax: 1-954-525-3261
Fax: 33-(0)-4-97-21-10-96
Internet: www.seavision.com
Internet: www.seavision.com
Email: sales@seavision.com
DOC:062212-5
Email: sales@seavisioneurope.com
SV10 LED
Underwater Light
Thru-Hull Mount, LED Array
