unGer nLite Hydro Power HP06T, Quick Start Manual

ungerglobal.com

Contents under pressure can cause severe injury 
or death from tank rupture. 

When starting system:

•฀฀Check฀system฀for฀cracks.
•฀Be฀sure฀cover฀is฀in฀locked฀position.
•฀Do฀not฀exceed฀฀pressure฀of฀115฀psi฀(8Bar).
•฀฀Keep฀discharge฀line฀open฀and฀hold฀yellow฀lever฀

down฀to฀remove฀trapped฀air฀from฀system.

•฀฀฀For฀use฀only฀with฀drinking฀water
Before฀servicing฀system:
•฀฀Shut฀off฀drinking฀water฀supply฀and฀open฀

waterfed฀wash฀pole฀tubing฀discharge฀line.

•฀Disconnect฀water฀supply฀and฀allow฀tank฀to฀drain.

DANGER

!

Spilled฀resin฀is฀a฀slipping฀hazard.
Clean฀up฀spilled฀resin฀immediately.

WARNING

!

Resin can cause skin irritation. 
Avoid skin contact.

Wash฀hands฀thoroughly฀after฀use.

Can cause eye irritation.
Avoid eye contact.

Wear฀safety฀goggles.
In฀case฀of฀eye฀contact,฀immediately฀flush฀
eyes฀thoroughly฀with฀clean฀water.฀฀

Consult฀doctor฀if฀symptoms฀persist.

CAUTION

!

STORAGE:

฀Do฀not฀store฀resin฀

in฀open฀or฀unlabeled฀containers.฀
Store฀in฀a฀cool฀(15°F฀to฀100°F),฀
dry฀place.

DISPOSAL: 

Dispose฀of฀in฀

accordance฀with฀applicable฀
federal,฀state/provincial,฀and฀
local฀regulations.

All฀Hydro฀Power฀models฀

require฀the฀use฀of฀mixed฀

bed฀ion฀exchange฀resin฀

(commonly฀referred฀to฀as฀

de-ionizing฀resin).฀฀

This฀resin฀will฀require฀

replacement฀and฀handling.

System Overview

The nLite HydroPower

TM

 – 

The Future of DI Systems... Today

• Inspect system – ensure DI resin bag(s) are installed.

• Set up system in upright position.

• Choose a stable onsite location.

• Quick connect fittings are supplied with the HydroPower system.

• Thread garden hose directly onto inlet connection on/off valve.

• Install quick connect adapter to waterfed wash pole hose.

• Ensure all waterfed wash pole on/off valves are in “OPEN” position.

• Inspect system as it pressurizes and begins producing “purewater”

• Turn on TDS meter and inspect “purewater” quality.  A reading of ‘0’ 

contains zero parts per million total dissolved solids).

• Adjust flow at waterfed wash pole brush head by:

        -  On/Off Valve

        -  Waterfed wash pole control (on/off) valve. 

• Disconnect waterfed wash pole tubing.

• Depress yellow lever on system head assembly.

• Use a counter-clockwise quarter-turn to release 

• Reach into housing and remove exhausted resin 

• Drop in new resin bag(s) by hand – be sure to seat bags 

with zip-tie facing up. Pat down bag by hand to 

• Inspect system head assembly: O-ring and 

 distribution filter are in good condition. 

Re-coat O-ring with silicone lubricant only.

• Re-install DI System head assembly, push down firmly, 

then quarter-turn clockwise.

• System is ready to be operated.

• Turn “ON’ water supply.

FastLock

TM

 Lever

Quick Connect Adapter

FloWater

TM

Distribution Filter

System Inlet
Connection for
On/Off Valve

TDS Meter

Output Valve

Housing with  
Rugged Outside  
Appearance

QuickChange

TM

Resin Bag

(Packed inside unit)