unGer nLite Hydro Power HP06T, Quick Start Manual

ungerglobal.com

•฀฀Check฀system฀for฀cracks.
•฀Be฀sure฀cover฀is฀in฀locked฀position.
•฀Do฀not฀exceed฀฀pressure฀of฀115฀psi฀(8Bar).
•฀฀Keep฀discharge฀line฀open฀and฀hold฀yellow฀lever฀

down฀to฀remove฀trapped฀air฀from฀system.

•฀฀฀For฀use฀only฀with฀drinking฀water
Before฀servicing฀system:
•฀฀Shut฀off฀drinking฀water฀supply฀and฀open฀

waterfed฀wash฀pole฀tubing฀discharge฀line.

•฀Disconnect฀water฀supply฀and฀allow฀tank฀to฀drain.

Spilled฀resin฀is฀a฀slipping฀hazard.
Clean฀up฀spilled฀resin฀immediately.

Wash฀hands฀thoroughly฀after฀use.

Wear฀safety฀goggles.
In฀case฀of฀eye฀contact,฀immediately฀flush฀
eyes฀thoroughly฀with฀clean฀water.฀฀
Consult฀doctor฀if฀symptoms฀persist.

฀Do฀not฀store฀resin฀

in฀open฀or฀unlabeled฀containers.฀
Store฀in฀a฀cool฀(15°F฀to฀100°F),฀
dry฀place.

Dispose฀of฀in฀

accordance฀with฀applicable฀
federal,฀state/provincial,฀and฀
local฀regulations.

All฀Hydro฀Power฀models฀
require฀the฀use฀of฀mixed฀
bed฀ion฀exchange฀resin฀
(commonly฀referred฀to฀as฀
de-ionizing฀resin).฀฀

This฀resin฀will฀require฀
replacement฀and฀handling.

System Set Up

LOCATE JOBSITE WATER SUPPLY

Unger recommends testing the onsite water supply for both tem-
perature and TDS (total dissolved solids) prior to working. Higher TDS 
levels reduce the DI systems capacity. 

• Inspect system – ensure DI resin bag(s) are installed.

• Set up system in upright position.

• Choose a stable onsite location.

CONNECT WATER SUPPLY (GARDEN HOSE) 
TO SYSTEM INLET CONNECTION

• Quick connect fittings are supplied with the HydroPower system.

• Thread garden hose directly onto inlet connection on/off valve.

CONNECT WATERFED WASH POLE TUBING

• Install quick connect adapter to waterfed wash pole hose.

• Ensure all waterfed wash pole on/off valves are in “OPEN” position.

TURN FEED WATER SUPPLY “ON” SLOWLY

• Inspect system as it pressurizes and begins producing “purewater”

• Turn on TDS meter and inspect “purewater” quality.  A reading of ‘0’ 

is best and indicates the system is running properly (product water  

contains zero parts per million total dissolved solids).

• Adjust flow at waterfed wash pole brush head by:

        -  On/Off Valve

        -  Waterfed wash pole control (on/off) valve. 

1

2

3

4

1

Building/Facility

2

3

4

Replacing DI Resin

SHUT-OFF FEED WATER SUPPLY

• Disconnect waterfed wash pole tubing.

• Depress yellow lever on system head assembly.

RELEASE SYSTEM HEAD ASSEMBLY

• Use a counter-clockwise quarter-turn to release 

system head assembly; remove and set aside.

• Reach into housing and remove exhausted resin 

by hand; discard according to local regulations.

REPLACE RESIN

• Drop in new resin bag(s) by hand – be sure to seat bags 

with zip-tie facing up. Pat down bag by hand to 

ensure seated properly.

• Inspect system head assembly: O-ring and 

FloWater

TM

 distribution filter are in good condition. 

Re-coat O-ring with silicone lubricant only.

• Re-install DI System head assembly, push down firmly, 

then quarter-turn clockwise.

• System is ready to be operated.

RECONNECT WATERFED WASH POLE TUBING

• Turn “ON’ water supply.

TEST SYSTEM TDS

1

2

3

4

5

1

2

3

4

5