background image

Quick Guide

UPO1000 Series

4/17

Grounding

Frame and chassis grounding terminal

Grounding

Protective grounding terminal

Grounding

Measurement grounding terminal

OFF

Main power off

ON

Main power on

Power

Supply

Standby power supply: when the power switch is turned off, this

device is not completely disconnected from the AC power supply.

CAT I

Secondary electrical circuit connected to wall sockets through transformers or

similar equipment, such as electronic instruments and electronic equipment;

electronic equipment with protective measures, and any high-voltage and

low-voltage circuits, such as the copier in the office.

CAT II

CATII: Primary electrical circuit of the electrical equipment connected to the indoor

socket via the power cord, such as mobile tools, home appliances, etc. Household

appliances, portable tools (e.g. electric drill), household sockets, sockets more than

10 meters away from CAT III circuit or sockets more than 20 meters away from CAT

IV circuit.

CAT III

Primary circuit of large equipment directly connected to the distribution board and

circuit between the distribution board and the socket (three-phase distributor

circuit includes a single commercial lighting circuit). Fixed equipment, such as

multi-phase motor and multi-phase fuse box; lighting equipment and lines inside

large buildings; machine tools and power distribution boards at industrial sites

(workshops).

CAT IV

Three-phase public power unit and outdoor power supply line equipment.

Equipment designed to “initial connection”, such as power distribution system of

power station, power instrument, front-end overload protection, and any outdoor

transmission line.

Certific

ation

CE indicates a registered trademark of EU.

Certific

ation

UKCA

indicates a registered trademark of the United Kingdom

.

Certific

ation

It conforms to UL STD 61010-1, 61010-2-030, CSA STD C22.2 No.61010-1 and

61010-2-030

.

Waste

This product complies with the marking requirements of WEEE Directive

(2002/96/EC). This additional label indicates that this electrical / electronic product

must not be discarded in household waste.

EFUP

This environment-friendly use period (EFUP) mark indicates that dangerous or toxic

substances will not leak or cause damage within this indicated time period. The

environment-friendly use period of this product is 40 years, during which it can be

used safely. Upon expiration of this period, it should enter the recycling system.

Safety Requirements

Warning

Summary of Contents for UPO1000 Series


















Reviews: