-
30.0
℃～-
20.1
℃
-
20.0
℃
40.0
℃
～
40.1
℃
70.0
℃
～
UT330THC
UT330TH
±
0.4
℃
±
0.4
℃
Temperature: 0.1°C; Humidity: 0.1%RH
64000 sets
10s
24h
～
Press the button to start the logger or start the
logger through the software (Immediately/delay/
at fixed time).
0min
240min, it defaults at 0 and can be
changed through the PC software.
～
0
～
255, it defaults at 0 and can be
changed through the PC software.
0s
10h, it defaults at 0 and can be
changed through the PC software.
～
10s
CR2032
140 days at an test interval of 15min (temperature 25
℃
)
Resolution
Logging capacity
Logging interval
Unit/alarm setting
Start mode
Logging delay
Device ID
Alarm delay
Screen off time
Battery type
Data export
Working time
Function
Temperature
Range
Accuracy
Accuracy
Specification
Working temperature & humidity
Storage temperature
Protection degree
-
30°C ~ 70°C,
≤
99%, non-condensable
-50°C~70°C
IP65
The default unit is °C. Alarm types include single and
accumulated alarm, the default type is single alarm.
Alarm type can be changed through the PC soft.
3.Start logging at preset fixed time
Mode 1: Long press the start button for 3 seconds in main interface to
start logging. This start mode supports start delay, if delay time is set,
the logger will start logging after a delayed time.
Mode 2: Start logging through the software: On PC software, when
parameter setting is completed, the logger will start logging after user
unplugs the logger from the computer.
Mode 3: Start the logger at preset fixed time: On PC software, when
parameter setting is completed, the logger will start logging at preset
time after user unplugs the logger from the computer. Mode 1 now is
disabled.
Warning: please replace the battery if low power indication is on.
Not logging
Logging
Delay logging
Logging at fixed time
Stopping the logger
There are two stop modes:
1.Press the button to stop
2.Stop logging through the software
Mode 1: In main interface, long press stop button for 3 seconds to stop the logger,
If "Stop with key" is not checked in the parameter interface, this function cannot be used.
Mode 2: After connecting the logger to the computer, click the stop icon on the main interface of the computer to
stop logging.
Recording mode
Normal: The logger automatically stops recording when the maximum number of groups is recorded.
Circulatory: When the maximum number of groups is recorded, the latest records will replace the earliest records in
turn. will show on the screen if this function is enabled.
Function Interface 1
UT330TH/
:Short press stop button to switch between temperature and humidity in the main interface.
UT330THC
In the main interface, short press the Start button to step through measured value, Max, Min, mean kinetic temperature,
upper alarm value, lower alarm value, current temperature unit, optional temperature unit (long press the Start and
Stop buttons at the same time to switch between the units), and measured value.
Users can short press stop button at any time to go back to the main interface. If no button is pressed for 10 seconds,
the logger will enter the power-saving mode.
Marking
When the device is in logging state, long press start button for 3 seconds to mark the current data for future reference,
the mark icon and current value will flash 3 times, total number of mark value is 10.
Function Interface 2
In the main interface, press the start button and stop button together for 3 seconds to enter the Function Interface 2, short
press start button to view: Y/M/D, device ID, maximum numbers of remaining storage groups, numbers of marking groups.
Alarm State
When the logger is operating,
Alarm disabled: Green LED flashes every 15 seconds and main interface displays
√.
Alarm enabled: Red LED flashes every 15 seconds and main interface displays ×.
No LED lights when the logger is in stopping state.
Note: The red LED will also flash when the low voltage alarm appears. Users should save the data in time and
the battery.
replace
Viewing data
Users can view the data in stop or operating state.
View the data in stop state: Connect the logger to the PC, if the LED flashes at this time, the PDF report is being
generated, do not unplug the logger at this time. After the PDF report is generated, users can click the PDF file to
view and export the data from the computer software.
View the data in operating state: Connect the logger to the PC, the logger will generate a PDF report for all previous
data, at the same time, the logger will continue logging data and it can only generate a PDF report with new data
the next time.
Alarm setting and result
Single:
The temperature (humidity) reaches or exceeds the set threshold. If the continuous alarm time is not less than
the delay time, the alarm will be generated. If the reading returns to normal within the delay time, no alarm will occur
.
If the delay time is 0s, an alarm will be generated immediately.
Accumulate:
The temperature (humidity) reaches or exceeds the set threshold. If the accumulated alarm time is not
less than the delay time, the alarm will be generated.
EMC
standard: EN61326-1 2013.
Download
Download the PC software according to the attached operation guide
Download the PC software from official website of UNI-T product center :http://www.uni-trend.com.cn
Instal
Double-click Setup.exe to install the software
Maintenance
Battery replacement (Figure 4)
Replace the battery with the following steps when the logger displays “ ”.
Rotate the battery cover counter-clockwise.
Install CR2032 battery and waterproof rubber ring(UT330TH)
Install the cover in arrow direction and rotate it clockwise.
Cleaning the logger
Wipe the logger with soft cloth or sponge dipped with a little water, detergent, soapy water.
Do not clean the logger with water directly to avoid damage to the circuit board.
±
0.8
℃
±
0.4
℃
±
0.8
℃
UT330T
/
/
Accuracy
Figure 4
0
99.9%RH
～
±
2.5%RH
±
2.5%RH
Humidity
/
View and export data in the PC software
View and export data
in the PC software
and smartphone APP
Can be set in the
PC software and
smartphone APP
1. Preparation
Please install the UT330THC APP on the smartphone first.
2. Installation
2.1 Search "UT330THC" in Play Store.
2.2 Search "UT330THC" and download on UNI-T's official website:
https://meters.uni-trend.com.cn/download?name=62
2.3 Scan the QR code on the right. (Note: APP versions may be updated without prior notice.)
3. Connection
Connect UT330THC's Type-C connector to the smartphone charging interface, and then open the APP.
Installation of UT330THC Android Smartphone APP
