Uniblitz VincentAssociates VED24 Instructions Manual Download

Page: 32 / 35

VED24 User Manual

Appendix

(Declaration

Conformity)

Declaration of Conformity

VA,

Inc.

dba

Vincent

Associates

Vincent Associates

803 Linden Avenue

Rochester, NY 14625

Tel: 800-828-6972

www.uniblitz.com

Description of Equipment:

The following product is manufactured in the United States of America by Vincent Associates:

Uniblitz VED24 Single-Channel Optical Shutter Controller

EU Declaration of Conformity (EMC):

Vincent Associates hereby declares that under its sole responsibility, and based on tests performed by G&M
Compliance Inc., that the aforementioned product meets the requirements of the

EU EMC Directive

2014/30/EU

by means of conformity to the following harmonized standards:

EN 61326-1: 2013

– EMC requirements for electrical equipment for measurement, control, and

laboratory use — Part 1: General requirements

IEC 61000-4-2:2008

– Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement

techniques - Electrostatic discharge immunity test

IEC 61000-4-3:2010

– Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement

techniques - Radiated, radio-frequency, electromagnetic field immunity test

IEC 61000-4-4:2012

– Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement

techniques - Electrical fast transient/burst immunity test

IEC 61000-4-5:2015

– Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement

techniques - Surge immunity test

IEC 61000-4-6:2013

– Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement

techniques - Immunity to conducted disturbances, induced by radio-frequency fields

IEC 61000-4-8:2009

– Electromagnetic compatibility (EMC) – Part 4-8: Testing and measurement

techniques – Power frequency magnetic field immunity test

IEC 61000-4-11:2004

– Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement

techniques - Voltage dips, short interruptions and voltage variations immunity tests

CISPR 11:2015

– Industrial, scientific and medical equipment - Radio-frequency disturbance

characteristics - Limits and methods of measurement

Summary of Contents for VincentAssociates VED24




































Search results

Summary of Contents for VincentAssociates VED24

Reviews:

Related manuals for VincentAssociates VED24

Brands by name

Popular brands

Uniblitz VincentAssociates VED24, Instructions Manual

Search results

Summary of Contents for VincentAssociates VED24

Reviews:

Related manuals for VincentAssociates VED24

Brands by name

Popular brands