background image

47

Fault finding

Description: Failure of the heating return sensor
(SRR)

Corrective action: Check the efficiency of the
sensor and/or wiring

Description: Over high temperature detected by
the heating sensor (SR) >203°F (>95°C)

Corrective action: Check the system’s water
circulation

Description:  Loss of flame signal during boiler
operation

Corrective action: Press the reset key on the panel

5

FAULT FINDING

2

1

3

5.1 - ERROR CODES

The boiler is fitted with an integrated 

diagnostic readout which,

in case of malfunction, consents the immediate individuation
of the type of fault directly on the control panel display

In the following fault finding table our purpose is to give some
technical information regarding the solutions to any problems
which could occur during boiler operation or commissioning
of the boiler.

When the fault signalling led (1) is on, press the LIGHT BLUE
key (2) to check the error code on the display (3).

Code:

Description: Mains voltage < 96 Vac

Corrective action: Check that the mains voltage
is <96 Vac, if the mains voltage is correct replace
the control board.

Code:

Description: Insufficient gas pressure

Corrective action: Check the pressure; if the
pressure is correct check the efficiency of the gas
pressure switch and/or the wiring.

Code:

Description: Difference between the heating
temperature sensor (SR) and the heating return
sensor (SRR) too high

Corrective action: Check the installation

Code:

Code:

Code:

Code:

Description: No flame detected during the ignition
phase.

Corrective action: Press the reset key on the
control panel

Code:

Description: Low water pression

Corrective action: Fill-up the water circuit

Code:

Description: Modulating fan failure

Corrective action: Check the fan’s wiring

Code:

Description: Modulating fan failure

Corrective action: Check the fan’s wiring

Code:

Description: Main heat exchanger frozen

Corrective action: Carefully de-frost the exchanger

Code:

Description: Intervention of the high limit
thermostat (TL)

Corrective action: Press the reset key on the
control panel

LIGHT
BLUE

VIOLET

YELLOW

BLUE

Summary of Contents for ALKON 70 kW





















































Reviews: