background image

12.  Unicla oil injector part no. OIRA803

Unicla oil injector can be used to 

add additional system oil during the 

evacuation or refrigerant charging 

process. Or alternatively any similar 

injection device can be used. 

13. Discharge line analysis - pressure and temperature

After commissioning a Unicla compressor for the first time, some basic pressure and thermal 

loading checks will determine if the operating environment for the compressor is within Unicla 

specifications, and whether compressor durability is being maximised.  The following chart should 

be used as a guide for UWX550 and UWX440 compressors to analyse normally acceptable high 

side (discharge/head) pressures and discharge line temperatures for given ambient conditions.

Discharge Line Pressure - Temperature Chart - Unicla UWX compressors

Ambient Ideal Discharge Pressure

Discharge Line Temp ˚C

Temp ˚C

Note:  Allow 20% tolerance for humidity above 60% relative humidity.

If the system high side pressure or discharge line superheat range is not within these parameters, 

reference to the Unicla Service Manual is required, or reference to additional technical information 

for specifications and faults regarding condensing to air differentials.

• NR

 = not recommended as a continuous running phase, superheat may exceed 40°C, however 

specific system design may allow for higher condensing capacity to maximise compressor 

durability and performance.

• • NR

 = not recommended in most instances, superheat may exceed 50°C, however if condensing 

capacity allows for < 50°C superheat, momentary running in this phase may be considered.

If any further assistance or information is required please go to www.unicla.hk

or contact your nearest Unicla dealer.

˚C

˚F

kPa

PSI

1800rpm

2200rpm

3500rpm

Discharge line 

Superheat range

15

60

600 - 800

90 - 115

37 - 42

42 - 47

50 - 56

7 - 26

18

65

750 - 950

110 - 135

43 - 52

47 - 58

56 - 70

9 - 34

21

70

900 - 1100

130 - 160

50 - 57

55 - 64

66 - 76

10 - 36

24

75

1050 - 1300

155 - 190

58 - 64

66 - 73

77 - 83

12 - 37

27

80

1200 - 1550

185 - 220

65 - 72

73 - 80

75 - 89

13 - 37

30

85

1400 - 1750

200 - 250

68 - 77

75 - 86

79 - 92

14 - 38

33

90

1500 - 1900

215 - 275

72 - 85

80 - 94

89 - 97

14 - 39

35

95

1700 - 2100

245 - 300

77 - 90

86 - 98

93 - 102

15 - 40

38

100 1850 - 2250

265 - 325

85 - 92

94 - 102

• NR

17 > 40

41

105

200 - 2400

290 - 350

88 - 97

97 - 108

• NR

18 > 40

44

110 2250 - 2650

325 - 385

92 - 102

• NR

• • NR

18 > 50

47

115 2500 - 2900

370 - 420

102 - 110

• NR

• •NR

20 > 50

8.

Summary of Contents for UWX440















Reviews: