Unicorn DB2-H515, Operation Manual

                    ★ 

사용  후  최소한  5분  대기후  전원을  off  시켜  콘센트로부터  전원코드를  분리시켜  놓으세요. 

                          그렇지  않으면  화재  시  높은  전압에  의한  심한  상해를  초래할  수  있습니다. 

설      치      시

      ★  기계  설치  시  반드시  숙련된  기술자가  설치   

                            하도록  하십시오.

                      ★  전기  작동  부  조작  필요시  자사의  A/S  센터   

                            로  연락  주시거나,  숙련된  기술자가  조작을   

                            하셔야  합니다. 

                      ★  본  기계는  31㎏  이상의  무게를  가지고  있으   

                            므로  2사람  이상이  옮겨야  안전합니다.

                      ★  테이블의  상판은  기계중량과  진동에  의한     

                            충격에  견디기  위해  40㎜이상의  두께로     

                            구성되어야  합니다.

                      ★  설치가  완전히  끝날  때  까지  전원  코드를     

                            연결하지  마십시오.  오작동에  의한  폐달     

                            작동  시  상해의  원인이  됩니다.

                      ★  접지가  설치되어  있는지  확인하십시오.  만약 

                            접지설치가  확실치  않을시  전기  충격  발생시 

                            치명적인  상해의  원인이  됩니다.

                      ★  모터를  설치  또는  사용  시에는  사용설명서를 

                            반드시  숙지하신  후  작업을  시작  하십시오.

★  모든  코드는  작동부로부터  25㎜  떨어져   

                              있어야  합니다.  과도한  코드의  굽힘   

                              또는  지나친  매듭은  화재나  전기  충격을   

                              발생시킬  수  있는  위험  요소가  됩니다.

                        ★  벨트  커버는  반드시  기계  상부와  모터에   

                              설치하신  후  사용하십시오.

                        ★  급유장치에  기름  또는  구리스  취급  시   

                                반드시  보호안경과  보호  장갑을  착용   

                                하십시오.  기름  또는  구리스가  당신의   

                                눈과  피부에  접촉되어  감염되는  것을   

                                막을  수  있습니다.

                                기름   또 는  구리 스를   절대   먹 지  말   것 이며 ,   

                                만일  상황  발생시에는  구토를  하거나   

                                가까운  병원을  방문하여  응급조치를   

                                받으십시오.

                        ★  장비  설치  시  기계  주위에는  강력한   

                                전기적  잡음을  일으키는  장비를  설치   

                                하지  마십시오.

                                예를  들어  높은  주파수를  발생시키는   

                                용접장치  설치  시  오작동을  일으킬  수   

                                있는  원인이  됩니다.   

사      용      시

      ★  본  제품은  반드시  숙련된  기술자가  사용해야   

                            되며,  본  제품을  다루기전  반드시  안전  교육   

                            을  실시하십시오.

                      ★  본  제품은  재봉기  본  용도  이외에는  어떤     

                            용도로도  사용할  수  없습니다.

                      ★  본  제품을  작동하기  전  반드시  모든  안전     

                            장치를  부착  하십시오.  만약,  안전장치를     

                            설 치하 지   않고   작 동   시   상 해의   원 인 이  됩 니 다.

                      ★  다음과  같은   상황시에는   반드시  전원을   끄십시오.

                        ①바늘에  실을  끼울  때

                        ②보빈이나  바늘  교체  시

                        ③ 기계 를  사용 하지   않거 나 ,  장시 간   자리 를  비울 시

★   재 봉   시   작동 부   또 는   압 력 장 치를   건들 지    

                                마십 시 오 .  그렇지  않으면  기계에  무리를   

                                주거나  상해의  원인이  됩니다.

                        ★  자동  노루발  장치  사용  시  솔레노이드부   

                              에  접촉을  피하십시오.  작동  시  열  발생   

                              으로  인한  화상상해의  원인이  됩니다.

                        ★  기계  작동  시  오작동  발생,  비정상적   

                                잡음,  타는냄새  발생시  즉시  전원을   

                                OFF후  가까운  자사의  A/S  센터로  연락   

                                주시기  바랍니다.

                        ★   본   제 품에   문 제  발생 시   자 사의   가 까운   A/S   

                                센 터  및   직 원에 게  연 락  주시 기  바랍 니다 .

ꍾ 

안전  주의

All manuals and user guides at all-guides.com