Unicorn LS2-H530, Operation Manual

          ★

  사용  후  최소한  5분  대기후  전원을  off  시켜  콘센트로부터  전원코드를  분리시켜  놓으세요. 

                            그렇지  않으면  화재  시  높은  전압에  의한  심한  상해를  초래할  수  있습니다. 

설      치      시

                    ★    기계  설치  시  반드시  숙련된  기술자가 

                            설치하도록  하십시오.

                    ★    전기  작동  부  조작  필요시  자사의  A/S 

                            센터로  연락  주시거나,  숙련된  기술자가 

                            조작을  하셔야  합니다. 

                    ★  본  기계는  34㎏  이상의  무게를  가지고     

                            있 으므 로   2사람   이 상 이  옮겨 야   안 전합 니다 .

                    ★    테이블의  상판은  기계중량과  진동에  의한   

                            충격에  견디기  위해  40㎜이상의  두께로     

                            구성되어야  합니다.

                    ★    설치가  완전히  끝날  때  까지  전원  코드를   

                            연결하지  마십시오.  오작동에  의한  폐달     

                            작동  시  상해의  원인이  됩니다.

                    ★  접지가  설치되어  있는지  확인하십시오.     

                            만약  접지설치가  확실치  않을시  전기충격   

                            발생시  치명적인  상해의  원인이  됩니다.

                    ★   모 터 를  설치   또 는   사 용   시 에는   사용 설 명서 를    

                          반 드 시   숙지 하 신   후  작 업 을  시 작   하 십 시 오 .

            ★  모든  코드는  작동부로부터  25㎜  떨어져     

                          있어야  합니다.  과도한  코드의  굽힘  또는     

                          지나친  매듭은  화재나  전기  충격을  발생     

                          시킬  수  있는  위험  요소가  됩니다.

                  ★  벨트  커버는  반드시  기계  상부와  모터에     

                          설치하신  후  사용하십시오.

                  ★  급유장치에  기름  또는  구리스  취급  시     

                          반드시  보호안경과  보호  장갑을  착용하십     

                          시오.  기름  또는  구리스가  당신의  눈과     

                          피부에  접촉되어  감염되는  것을  막을  수     

                          있습니다.

                              기름  또는  구리스를  절대  먹지  말  것이며,   

                              만일  상황  발생시에는  구토를  하거나     

                              가까운  병원을  방문하여  응급조치를  받으   

                              십시오.

                  ★  장비  설치  시  기계주위에는  강력한  전기적     

                          잡 음 을  일 으키 는   장 비 를   설 치 하 지  마 십시 오 .

                          예를  들어  높은  주파수를  발생시키는  용접   

                          장치  설치  시  오작동을  일으킬  수  있는     

                          원인이  됩니다.       

사      용      시

★     본     품 은   반 드 시  숙 련된   기 술 자 가  사용 해    

                            야   되며,  본  제품을  다루기전  반드시  안전   

                            교육을  실시하십시오.

                    ★    본  제품은  재봉기  본  용도  이외에는  어떤   

                            용도로도  사용할  수  없습니다.

                    ★    본  제품을  작동하기  전  반드시  모든  안전   

                            장치를  부착하십시오.  만약,  안전장치를     

                            설치하지  않고  작동  시  상해의  원인이     

                            됩니다.

                    ★   다 음 과   같 은   상 황 시에 는   반 드 시   전 원 을      

                            끄 십 시 오 .

                          ①  바늘에  실을  끼울  때

                          ②  보빈이나  바늘  교체  시

                          ③   기 계 를  사 용 하 지   않 거 나 ,  장시 간   자 리 를    

                                비 울 시

                ★  재 봉   시   작 동부   또 는   압력 장 치 를   건들 지      

                              마 십시 오 .  그렇지  않으면  기계에  무리를     

                            주거나  상해의  원인이  됩니다.

                      ★  자동  노루발  장치  사용  시  솔레노이드부에   

                            접촉을  피하십시오.  작동  시  열  발생으로     

                            인한  화상상해의  원인이  됩니다.

                      ★  기계  작동  시  오작동  발생,  비정상적  잡음,   

                            타는  냄새  발생시  즉시  전원을  OFF후     

                            가까운  자사의  A/S  센터로  연락  주시기     

                            바랍니다.

                      ★  본  제품에  문제  발생시  자사의  가까운 

                            A/S  센터  및  직원에게  연락  주시기

                            바랍니다.

ꍾ

  안전  주의