background image

17

5. Press and hold 

PRIORITY

key. The PRI Icon 

appears in the LCD display.

To enter the Priority Scan Mode

Momentarily press the 

PRIORITY

key. PRI Icon appears in the display.

To exit the Priority Scan Mode

Momentarily press the 

PRIORITY

key again. PRI Icon disappears from the display.

Channel Lockout

You can lock out a channel so it is not scanned. Locked out does not erase the
frequency from the channel. You can lock out up to 29 channels, including the
Priority channel, but not all 30 channels. Lockout information is retained in
memory when the scanner is turned off.

To Lockout a Channel

Example: Suppose you want to lock out Channel 2 because it stops on transmissions
you dont want to hear.

Press 

LOCKOUT

when the scanner stops on 

Channel 2. The scanner locks out Channel 2,
immediately advances to the next channel
that is not locked out, and resumes
scanning. In the Manual mode, press

LOCKOUT

to lock out the displayed

channel. Pressing 

LOCKOUT

does not

advance to the next channel in Manual mode.

L/O appears in the LCD display to indicate the displayed channel is locked out. 

Whenever you want to search for channels that are locked out, press 

Manual

repeatedly to go through all 30 channels. If a channel is locked out, the L/O Icon 
is displayed.

BC244clt.qxd  2/10/99  3:34 PM  Page 17

Summary of Contents for BC244CLT

























Reviews: