Uniden Grant LT User Manual Download

Page: 10 / 17

SWR Meter

Measures

SWR

(standing wave ratio) of antenna. Use to check antenna

system or to adjust your antenna to the proper length.

To measure

SWR

1. Set the Mode Selector to the

position.

2. Set the Meter Selector

to the

CAL

position.

3. Press and hold the microphone

PTT

Switch. (Transmit)

4. Calibrate the meter using the

SWR CAL

Control. (Adjust the

needle to the

▼

mark.) Do not

talk into the microphone or set
the

MIC GAIN

Control to the

MIN

position.

5. Move the Meter Selector to the

SWR

position while holding the

PTT

Switch.

A reading below 2 is acceptable. Higher readings indicate a problem in the antenna
system. Problems may be caused by humidity, vibration, or corrosion. Check both
ends of the coaxial cable connector. Also check for damage to the cable or antenna.

ullttii--F

nccttiio

n M

Meetteerr

Grant LT.qxd 3/31/99 10:03 AM Page 8

Summary of Contents for Grant LT


















Search results

Summary of Contents for Grant LT

Reviews:

Related manuals for Grant LT

Brands by name

Popular brands

Uniden Grant LT, User Manual

Search results

Summary of Contents for Grant LT

Reviews:

Related manuals for Grant LT

Brands by name

Popular brands