Uniden Grant LT User Manual Download

Page: 8 / 17

1. Turn unit

and set

VOLUME

Control to a

comfortable level.

2. Select

CHANNEL

3. Set switch to

NB/ANL.

Dynamic Squelch Control

automatically sets Squelch to the optimal level for stronger

transmission and signal clarity. To scan for weaker signals, turn

Dynamic Squelch

Control

off and perform the following steps:

4a. Turn

SQUELCH

fully clockwise so only strong

signals can get through.

4b. Turn

SQUELCH

fully counter-clockwise until you

hear a hiss. Everything gets through - noise, weak
signals, and strong signals.

4c. Turn

SQUELCH

back clockwise until the hiss stops.

Only clearer signals get through.

Be sure that the power source, antenna, and microphone
are properly connected before proceeding.

o R

Reecceeiiv

vee

Set

SQUELCH

only

when the

radio is not receiving a
strong signal.

Grant LT.qxd 3/31/99 10:03 AM Page 6

Summary of Contents for Grant LT


















Search results

Summary of Contents for Grant LT

Reviews:

Related manuals for Grant LT

Brands by name

Popular brands

Uniden Grant LT, User Manual

Search results

Summary of Contents for Grant LT

Reviews:

Related manuals for Grant LT

Brands by name

Popular brands