background image

 

18          

888-994-7636

 

 
RECOMMENDED CLEANERS FOR YOUR STAINLESS STEEL INCLUDE THE 
FOLLOWING: 
 

JOB 

CLEANING AGENT 

COMMENTS 

Routine cleaning 

Soap, ammonia, detergent 
Medallion 

Apply with a sponge or cloth 

Fingerprints and smears 

Arcal 20, Lac-O-Nu, Ecoshine  Provides a barrier film 

Stubborn stains and 
discoloration 

Cameo, Talc, Zud, First 
Impression 

Rub in the direction of the 
polish lines 

Greasy and fatty acids, 
blood, burnt-on foods 

Easy-Off, Degrease It, Oven 
Aid 

Excellent removal on all 
finishes 

Grease and Oil 

Any good commercial 
detergent 

Apply with a sponge or cloth 

Restoration/Preservation  Benefit, Super Sheen 

Good idea monthly 

Reference:  Nickel Development Institute, Diversey Lever, Savin, Ecolab, NAFEM. 

 

NOTE:  Do not use steel pads, wire brushes, scrapers, or chloride cleaners 
to  clean  your  stainless  steel.    CAUTION:    DO  NOT  USE  ABRASIVE 
CLEANING  SOLVENTS,  AND  NEVER  USE  HYDROCHLORIC  ACID 
(MURIATIC ACID) ON STAINLESS STEEL. 

NOTE:    Do  not  pressure  wash  equipment  as  damage  to  electrical 
components may result. 

 

Proper  maintenance  of  equipment  is  the  ultimate  necessity  in  preventing  costly 
repairs.  By evaluating each unit on a regular schedule, you can often catch and 
repair  minor  problems  before  they  completely  disable  the  unit  and  become 
burdensome on your entire operation. 

For more information on preventive maintenance, consult your local service 
company or CFESA member.

  Most repair companies offer this service at very 

reasonable rates to allow you the time you need to run your business along with 
the  peace  of  mind  that  all  your  equipment  will  last  throughout  its  expected  life.  
These  services  often  offer  guarantees  as  well  as  the  flexibility  in  scheduling  or 
maintenance for your convenience. 

For a complete listing of current Randell ASA please visit 

www.unifiedbrands.net

 

Randell believes strongly in the products it manufactures and backs those products 
with  one  of  the  best  warranties  in  the  industry.    We  believe  with  the  proper 
maintenance and use, you will realize a profitable return on your investment and 
years of satisfied service. 

 

Preventive Maintenance (cont.) 

Summary of Contents for Randell 2127AC
























Reviews: