background image

OM-DEEP WELL REFRIGERATOR SERIES       19

Orders canceled prior to production scheduling entered into engineering/production and cancelled are subject to a cancellation charge 

(contact factory for details).

STORAGE CHARGES

Unified Brands makes every effort to consistently meet our customer’s shipment expectations.  If after the equipment has been 

fabricated, the customer requests delay in shipment, and warehousing is required:

1.  Equipment held for shipment at purchasers request for a period of 30 days beyond original delivery date specified will be invoiced 

and become immediately payable.

2.  Equipment held beyond 30 days after the original delivery date specified will also include storage charges.

SHIPPING & DELIVERY

Unified Brands will attempt to comply with any shipping, routing or carrier request designated by dealer, but reserves the right to ship 

merchandise via any responsible carrier at the time equipment is ready for shipment.  Unified Brands will not be held responsible for 

any carrier rate differences; rate differences are entirely between the carrier and purchaser.  Point of shipping shall be determined by 

Unified Brands (Weidman, MI/Prior, OK/Jackson, MS).  At dealer’s request, Unified Brands will endeavor whenever practical to meet 

dealer’s request.  Freight charges to be collect unless otherwise noted.

DAMAGES

All crating conforms to general motor carrier specifications.  To avoid concealed damage, we recommend inspection of every carton 

upon receipt.  In the event the item shows rough handling or visible damage to minimize liability, a full inspection is necessary upon 

arrival.  Appearance of damage will require removing the crate in the presence of the driver.  

A notation must be placed on the 

freight bill and signed for by the truck driver at the time of delivery.

   Any and all freight damage that occurs to a Unified Brands 

piece of equipment as a result of carrier handling is not considered under warranty, and is not covered under warranty guidelines.  Any 

freight damage incurred during shipping needs to have a freight claim filed by the receiver with the shipping carrier.  Consignee is 

responsible for filing of freight claims when a clear delivery receipt is signed.  Claims for damages must be filed immediately (within 10 

days) by the consignee with the freight carrier and all cartons and merchandise must be retained for inspection.  Internal or concealed 

damage may fall under Unified Brands responsibility dependent upon the circumstances surrounding each specific incident and are at 

the discretion of the Unified Brands in-house service technician.

 

RETURNED GOODS

Authorization for return must first be obtained from Unified Brands before returning any merchandise.  Any returned goods shipment 

lacking the return authorization number will be refused, all additional freight costs to be borne by the returning party.  Returned 

equipment must be shipped in original carton, freight prepaid and received in good conditions.  Any returned merchandise is subject 

to a minimum handling charge (contact factory for details).

INSTALLATION

 

Equipment installation is the responsibility of the dealer and/or their customer.

Unified Brands requires all equipment to be professionally installed.

PENALTY CLAUSES

 

Dealer penalty clauses, on their purchase order or contractually agreed to between the dealer and their clients are not binding on 

Unified Brands.  Unified Brands does not accept orders subject to penalty clauses.  This agreement supersedes any such clauses in 

dealer purchase orders.

Warranty Policies

Summary of Contents for randell 4337DWR-290




















Reviews: