background image

I n s t a l l a t i o n   &   P r o g r a m m i n g   M a n u a l  

68

 

 

Extension wiring 

206/208 systems only: 

To eliminate cross-talk, it is a requirement that twisted pair cable must be 

used to support all extensions and system integral devices with only one terminal per cable. Four-

wire cable must be used. Individual cable-runs between the extension device and the MDF 
Connection Terminals is a mandatory requirement (Star-Wiring technique). 

Cable run lengths 

Extension type 

Cable run length 

206/208 systems 

Cable run length

212 system 

Single Line Telephone Extensions (900

) (using 0.4mm² cable)  3285m   

2000m 

Executive / Standard Terminals / Door phone (Mains power 

using 0.4mm² cable) 

950 m  

500m 

Executive / Standard Terminals / Door phone (Battery Back-

up using 0.4mm² cable) 

200 m  

500m 

If an ordinary telephone is connected to an extension which previously had a Terminal connected, 
the system needs to be told that the Terminal is no longer connected. Ringing will not be heard at the 

extension until this has been done, though dialling will still be possible. After plugging in the SLT, go 
off-hook and enter the code *750 ext #. 

Power Failure Transfer 

In the event of a power fail the analogue exchange lines will be connected directly to the designated 

power fail extensions as shown in the table below. The system Executive and Standard Terminal will 
not function correctly in the event of a power fail and should not be connected to these extensions. 

Exchange 

Line 

206 

208 

212 

11 11 11 

15 (requires 1+2 in expansion 
slot 1) 

12 12 

17 (requires 1+2 in expansion 
slot 2) 

21 (Requires 1+2 or 2+2 in 
expansion slot 1) 

25 (Requires 2+2B in 
expansion slot 1) 

4 - 

None 

None 

23 (Requires 1+2 or 2+2 in 

expansion slot 2) 

27 (Requires 2+2B in 

expansion slot 2) 

6 - 

None 

None 

The power fail telephone must match the line signalling characteristics provided by the network 
carrier. The optional Executive or Standard Terminal should not be connected to a power fail 
extension as it will not function in power fail mode. 

External wiring protection 

The 206 system have overvoltage protection on extension 14, the 208 system have overvoltage 
protection on extensions 14, 21 and 23 and 212 systems have overvoltage protection on  the  

extensions 11, 12, 14, 25 and 27 are suitable for outdoor cable runs. No other extensions are suitable 
for external use without additional external lightning protection. 

Connecting terminals to 206/208 systems 

When installing the Executive or Standard Terminal the signalling pair are polarity dependent. The 

speech pair is connected to the normal speech connections for the extension. The signalling pair is 
connected to any of the signalling pairs shown in Figure 4-4, each of the pins are labelled also on the 
casing under the MDF cover. When the speech wires are correctly wired then the terminal LED's 
will flash and it will be possible to make a call. If the signalling wiring is reversed then the display will 

show ‘Communication Error’ on the Executive Terminal screen and the Line 1 lamp will flash 
repeatedly after a short delay and the LEDs will not function on the Standard Terminal. While there 
is a communication error the terminal will beep every 2 seconds and the Line 1 key will flash until the 
wiring problem is resolved. 

After connecting the Executive Terminal or Standard Terminal with correct wiring the extension will 

automatically configure itself and the display will show ‘This is extension: xx’ on the Executive 

Important! 

Important! 

Summary of Contents for Small Office

































































































Reviews: