background image

PART III: OPERATION

42

Adjusting the gas valves group and removing the filter

1

2

5

3

4

3

5

0

2

4

Check the filter at least once a year!

Change the filter if the pressure difference between pressure connection 1 and 3 (Fig. 1-Fig. 3)is 

p > 10 

mbar.

Change the filter if the pressure difference between pressure connection 1 and 3  (Fig. 1-Fig. 3) is twice as high 

compared to the last check.

You can change the filter without removing the fitting.
1

Interrupt the gas supply closing the on-off valve.

2

Remove screws 1 ÷ 4 using the Allen key n. 3 and remove filter cover 5 in Fig. 5.

3

Remove the filter 6 and replace with a new one.

4

Replace filter cover 5 and tighten screws 1 ÷ 4 without using any force and fasten.

5

Perform leakage and functional test, p

max.

 = 360 mbar.

6

Pay attention that dirt does not fall inside the valve.

Check the filter at least once a year!

Change the filter if the pressure difference between pressure connection 1 and 2  (Fig. 1-Fig. 2) 

p> 10 mbar.

Change the filter if the pressure difference between pressure connection 1 and 2 (Fig. 1-Fig. 2) is twice as high

compared to the last check.

You can change the filter without removing the fitting.
1

Interrupt the gas supply closing the on-off valve.

2

Remove screws 1 ÷  6  (Fig. 3).

3

Change filter insert.

4

Re-insert filter housing, screw in screws 1 ÷ 6 without using any force and fasten.

5

Perform leakage and functional test, p

max.

 = 360 mbar.

6

Pay attention that dirt does not fall inside the valve.

MULTIBLOC DUNGS MB-DLE 405..412

DUNGS MB-DLE 415 - 420 B01 1” 1/2 - 2”

1
2
5
3
4

6

5

3

4

5

3 4

6

6

2

1

0

Fig. 27

Fig. 28

Fig. 29

Fig. 30

Fig. 31

Fig. 32

B

A

C

D

E

A

C

B

D

E

Summary of Contents for P75R








































































































































Reviews: